08-22-2006
I got the laptop working (it is an old Twinhead A5000) with a basic install of Gentoo. However, I am running Gnome and I cannot find a terminal emulator. I think I can run X11 and get a terminal emulator, but, I can't figure out how to load X11. More research required.
Still, the x86 box is actually running, so I should be able to start working on the sparc box later this week.
Thanks to everyone for their help so far.
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi,
I'm facing problem in connecting a Raid A1000 to E250 and E450. ( Both machines with Solaris 2.6 OS and patched, with different
scsi-initiator-ids - 7 & 3 ).
BTW, I'm not using this setup to access raid data from both machines simultaneously. There is Veritas Cluster Server monitoring... (1 Reply)
Discussion started by: shibz
1 Replies
2. UNIX Benchmarks
==============================================================
BYTE UNIX Benchmarks (Version 3.11)
System -- SunOS xxxxx 5.8 Generic_108528-13 sun4u sparc SUNW,Ultra-250
Start Benchmark Run: Sun Jan 11 19:47:12 EST 2004
1 interactive users.
Dhrystone 2 without register variables ... (0 Replies)
Discussion started by: kduffin
0 Replies
3. Solaris
Hi,
I have cisco console cable. One end of the cable is DB9 connector and the other end is RJ45 connector. I would like to use this cable to connect to my SUN E250 system from my pc so that I can access the SUn console directly.
I would like to know whether it is possible and also on which... (5 Replies)
Discussion started by: RajaRC
5 Replies
4. Solaris
Hi,
We have an E250 which we need to access to install solaris 10 for a communigate trial.
We only have the server itself, no cables or anything and im struggling to gain access.
It has a RSC card, that i have learned, but a db25-db9 cable doesn't seem to bring anything up in telnet on... (11 Replies)
Discussion started by: e250user
11 Replies
5. Solaris
Hi,
I need some help, since I am new to cluster.
I am handling a site where I have look after two SUN E250 server.
I have been asked to configure Active-Active Clustering on these servers.
I would like to know how to configure both the servers for clustering.
Below are the things which... (5 Replies)
Discussion started by: RajaRC
5 Replies
6. Solaris
Hello,
Running a Sun Solaris 9 E250 and need advice or suggestions on what type of external hard disks are compatible and or available. It's an old machine and is due for replacement soon but in the short term need an external hard drive for backup etc as the partner/backup machine has just... (2 Replies)
Discussion started by: KenLynch
2 Replies
7. Solaris
I've got an old E250 server where a front error LED is showing. I've read through the Sun docs (Sun Enterprise 250 Server Owner's Guide - Sun Microsystems) but it's only the 'General fault' LED (About the Status and Control Panel (Sun Enterprise 250 Server Owner's Guide) - Sun Microsystems)... (2 Replies)
Discussion started by: aussieos
2 Replies
8. Solaris
Hi everybody, my name is Giulia and for me is the fist time in this forum, i hope write in the correct section for my problem.
I have a sun solaris server e250 enterprise with sun 5 versionof O.S.
Now i wont format all and install new version of solaris, but i don't know the actual corrent... (7 Replies)
Discussion started by: giulia79
7 Replies
9. Solaris
E250 server only shows banner when powered on i am not getting OK PROMPT . .In morning it was booting with solaris 7 .i am not able to do STOP-A STOP-D .its not excepting STOP-N also.
Please help (1 Reply)
Discussion started by: monu94
1 Replies
LEARN ABOUT SUSE
lxterminal
LXTERMINAL(1) http://LXDE.org LXTERMINAL(1)
NAME
lxterminal - a lightweight terminal emulator based on GTK+ for the LXDE desktop.
SYNOPSIS
lxterminal [options...]
DESCRIPTION
This manual page documents briefly the lxterminal command.
lxterminal is a program that provides a terminal emulator for the desktop, usually for LXDE. It is a lightweight GTK+ 2.x based desktop
panel.
OPTIONS
This program follows the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is included
below.
-e STRING --command=STRING
Execute the argument to this option inside the terminal.
-t STRING --title=STRING
Set the terminal's title.
--working-directory=DIRECTORY
Set the terminal's working directory.
--geometry=CHARACTERSxLINES
Set the terminal's size in characters and lines.
-l --loginshell
Executes login shell.
AUTHOR
This manual page was written by paulliu grandpaul@gmail.com for the Debian system (but may be used by others). Permission is granted to
copy, distribute and/or modify this document under the terms of the GNU General Public License, Version 2 any later version published by
the Free Software Foundation.
On Debian systems, the complete text of the GNU General Public License can be found in /usr/share/common-licenses/GPL.
AUTHOR
Ying-Chun Liu
Author.
COPYRIGHT
Copyright (C) 2008 paulliu
http://LXDE.org Jun 28, 2008 LXTERMINAL(1)