Sponsored Content
Full Discussion: Uses for a Sun e250?
Operating Systems Linux Gentoo Uses for a Sun e250? Post 302086167 by kccrusher on Tuesday 22nd of August 2006 05:22:54 PM
Old 08-22-2006
I got the laptop working (it is an old Twinhead A5000) with a basic install of Gentoo. However, I am running Gnome and I cannot find a terminal emulator. I think I can run X11 and get a terminal emulator, but, I can't figure out how to load X11. More research required.

Still, the x86 box is actually running, so I should be able to start working on the sparc box later this week. Smilie

Thanks to everyone for their help so far.
 

9 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Raid A1000 with E450 and E250.

Hi, I'm facing problem in connecting a Raid A1000 to E250 and E450. ( Both machines with Solaris 2.6 OS and patched, with different scsi-initiator-ids - 7 & 3 ). BTW, I'm not using this setup to access raid data from both machines simultaneously. There is Veritas Cluster Server monitoring... (1 Reply)
Discussion started by: shibz
1 Replies

2. UNIX Benchmarks

Sun E250 / 512MB Ram

============================================================== BYTE UNIX Benchmarks (Version 3.11) System -- SunOS xxxxx 5.8 Generic_108528-13 sun4u sparc SUNW,Ultra-250 Start Benchmark Run: Sun Jan 11 19:47:12 EST 2004 1 interactive users. Dhrystone 2 without register variables ... (0 Replies)
Discussion started by: kduffin
0 Replies

3. Solaris

SUN E250 Console connectivity

Hi, I have cisco console cable. One end of the cable is DB9 connector and the other end is RJ45 connector. I would like to use this cable to connect to my SUN E250 system from my pc so that I can access the SUn console directly. I would like to know whether it is possible and also on which... (5 Replies)
Discussion started by: RajaRC
5 Replies

4. Solaris

E250 - need to access it

Hi, We have an E250 which we need to access to install solaris 10 for a communigate trial. We only have the server itself, no cables or anything and im struggling to gain access. It has a RSC card, that i have learned, but a db25-db9 cable doesn't seem to bring anything up in telnet on... (11 Replies)
Discussion started by: e250user
11 Replies

5. Solaris

SUN E250 Cluster

Hi, I need some help, since I am new to cluster. I am handling a site where I have look after two SUN E250 server. I have been asked to configure Active-Active Clustering on these servers. I would like to know how to configure both the servers for clustering. Below are the things which... (5 Replies)
Discussion started by: RajaRC
5 Replies

6. Solaris

Sun Solaris 9 E250 -- Suggestions For External Hard Drives

Hello, Running a Sun Solaris 9 E250 and need advice or suggestions on what type of external hard disks are compatible and or available. It's an old machine and is due for replacement soon but in the short term need an external hard drive for backup etc as the partner/backup machine has just... (2 Replies)
Discussion started by: KenLynch
2 Replies

7. Solaris

Error LED showing on E250

I've got an old E250 server where a front error LED is showing. I've read through the Sun docs (Sun Enterprise 250 Server Owner's Guide - Sun Microsystems) but it's only the 'General fault' LED (About the Status and Control Panel (Sun Enterprise 250 Server Owner's Guide) - Sun Microsystems)... (2 Replies)
Discussion started by: aussieos
2 Replies

8. Solaris

Sun Solaris Enterprise E250 x64 Help

Hi everybody, my name is Giulia and for me is the fist time in this forum, i hope write in the correct section for my problem. I have a sun solaris server e250 enterprise with sun 5 versionof O.S. Now i wont format all and install new version of solaris, but i don't know the actual corrent... (7 Replies)
Discussion started by: giulia79
7 Replies

9. Solaris

E250 server not getting ok prompt

E250 server only shows banner when powered on i am not getting OK PROMPT . .In morning it was booting with solaris 7 .i am not able to do STOP-A STOP-D .its not excepting STOP-N also. Please help (1 Reply)
Discussion started by: monu94
1 Replies
Xsession.options(5)						File Formats Manual					       Xsession.options(5)

NAME
Xsession.options - configuration options for Xsession(5) DESCRIPTION
/etc/X11/Xsession.options contains a set of flags that determine some of the behavior of the Xsession(5) Bourne shell (sh(1)) script. See the Xsession(5) manpage for further information. Xsession.options may contain comments, which begin with a hash mark ('#') and end at the next newline, just like comments in shell scripts. The rest of the file consists of options which are expressed as words separated by hyphens, with only one option per line. Options are enabled by simply placing them in the file; they are disabled by prefixing the option name with 'no-'. Available options are: allow-failsafe If the 'failsafe' argument is passed to the Xsession script, an emergency X session is invoked, consisting of only an x-termi- nal-emulator(1) in the upper-left hand corner of the screen. No window manager is started. If an x-terminal-emulator program is not available, the session exits immediately. allow-user-resources If users have a file called .Xresources in their home directories, these resources will be merged with the default X resources when they log in. allow-user-xsession If users have an executable file called .xsession in their home directories, it can be used as the startup program for the X session (see Xsession(5)). If the file is present but not executable, it may still be used, but is assumed to be a Bourne shell script, and executed with sh(1). use-session-dbus If the dbus package is installed, the session bus will be activated at X session launch. use-ssh-agent If the ssh-agent(1) program is available and no agent process appears to be running already, the X session will be invoked by exec'ing ssh-agent with the startup command, instead of the startup command directly. All of the above options are enabled by default. Additional options may be supported by the local administrator. Xsession(5) describes how this is accomplished. AUTHORS
Stephen Early, Mark Eichin, and Branden Robinson developed Debian's X session handling scripts. Branden Robinson wrote this manual page. SEE ALSO
Xsession(5), ssh-agent(1), x-terminal-emulator(1) Debian Project 2004-10-31 Xsession.options(5)
All times are GMT -4. The time now is 06:26 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy