08-22-2006
SCO Unix Network Configuration
Hello Guys,
We have an old PC running on SCO Unix V. Is there any sites where i can get manual/procedures on how to install and configure Network. Thanks
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 90.0.0.99). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg
Can anyone tell... (1 Reply)
Discussion started by: potter
1 Replies
2. HP-UX
Hi,
I have installed a HP-UX B.11.00 U 9000/800 Server in one of the domain. And I'm also able to telnet/ping into this server from systems in the same domain.
But I'm not able to telnet/ping into this server from a different domain.
So, what shoud need to do to achieve this... (6 Replies)
Discussion started by: S.Vishwanath
6 Replies
3. SCO
I have got a Sco Unix Server, i want to connect some windows workstations. What configurations do i need to make on server and or workstation? (1 Reply)
Discussion started by: tpurazi1
1 Replies
4. Solaris
hi again...
i configured my network settings sometiime ago using the sys-unconfig command.the active link was rtls0.
there was some problem with the network so i changed the ISP. now when im trying to reconfigure the system wit sys-unconfig, it tries to configure the network on rtls1 (and shows... (1 Reply)
Discussion started by: strider
1 Replies
5. UNIX for Dummies Questions & Answers
I am using solaris 10, my internet works alright but each time i reboot i keep loosing my connection. I will have to use the
ifconfig iprb0 192.168.1.xx netmask 255.255.255.0 up and
Route add default 192.168.1.xxx command to gain back my internet.
I know there is a better way of addressing... (1 Reply)
Discussion started by: seyiisq
1 Replies
6. SCO
Dear Team ,
how i can configure raid 1 (mirroring) using ide hdd in sco open unix 5
i have two 80gb identical hdd (same make/model)
thanx (0 Replies)
Discussion started by: sudhir69
0 Replies
7. SCO
We have many remote servers that are running different versions of the SCO operating system. The current server inventory includes the usage of SCO 3.2v5.0.5 3.2v5.0.6 and 3.2v5.0.7.
Recently, there have been some ongoing problems when a re-boot is done with some of these remote servers.... (0 Replies)
Discussion started by: dclary
0 Replies
8. SCO
hi
i installed sco unix open server 5.0.7 on virtual machine vmware and runing it,
its work perfect and good.
now how i can configuare network at scoadmin that i able to access nework ?
---------- Post updated at 08:56 AM ---------- Previous update was at 01:47 AM ----------
nobody can... (2 Replies)
Discussion started by: farzad226
2 Replies
9. SCO
Hi,
I am really new to the forum and for SCO as well. I have a burning situation here to know how to configure below list of hardware into SCO 5.0.7!!
EQUINOX 990209-1 ELS 16 PORT TERMINAL SERVER and
Seagate DAT Scorpion 24 - Tape drive ( 12 GB / ) DDS-3 SCSI
Can Any One Please Help Me... (11 Replies)
Discussion started by: Kanthi Kiran
11 Replies
10. SCO
hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback.
show message :
dlpid:unable to open network adapter driver... (14 Replies)
Discussion started by: moein.mojtaba
14 Replies
LEARN ABOUT REDHAT
install-netsync
install-netsync(1) General Commands Manual install-netsync(1)
NAME
install-netsync - reads or sets the Network Preferences information on a Palm Device
SYNOPSIS
install-netsync -p /dev/pilot -e -n <hostname> -i <ip> -m <netmask>
DESCRIPTION
install-netsync allows the user to read or change the Network Preferences stored on the Pilot
OPTIONS
-p --port <port>,
Use device file port to communicate with the Palm handheld device. If this is not specified, will look for the $PILOTPORT environ-
ment variable. If both are not found, will fall back to /dev/pilot.
-h --help
Display help synopsis for install-netsync
-v --version
Display version of install-netsync
-e --enable
Enable the LanSync operation (instead of local HotSync)
-n --name <hostname>,
Sets the hostname of the remote machine you wish to connect to. This is not the hostname of the Palm device itself
-i --ip
Set the IP address of the remote machine you wish to connect to. This is not the IP address of the Palm device itself
-m --mask
Set the netmask of the remote machine you wish to connect to. This is not the netmask address of the Palm device itself
USAGE
The program will connect to a target Palm handheld device, and read or set the Network Preferences information specified or display the
Network Preferences stored on the Palm device
KNOWN BUGS
install-netsync has no known bugs.
REPORTING BUGS
Report bugs at http://bugs.pilot-link.org/
AUTHOR
install-netsync was created from the original install-user
application originally written by D. Jeff Dionne <jeff@RyeHam.ee.ryerson.ca>, and was split it out into a separate conduit by JP Rosevear
<jpr@ximian.com>
Free Software Foundation Palm Computing Device Tools install-netsync(1)