Sponsored Content
Full Discussion: Uses for a Sun e250?
Operating Systems Linux Gentoo Uses for a Sun e250? Post 302086009 by kccrusher on Monday 21st of August 2006 08:53:28 PM
Old 08-21-2006
UltraSparc equals 64?

The research I have done so far says the E250 is an ultrasparc, which is 64bit. Is this incorrect? Or were you saying you feel Gentoo will also drop support for the 64 bit sparcs?

Do you have another gnu/linux you recommend for this platform.

Thanks for your input.
 

9 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Raid A1000 with E450 and E250.

Hi, I'm facing problem in connecting a Raid A1000 to E250 and E450. ( Both machines with Solaris 2.6 OS and patched, with different scsi-initiator-ids - 7 & 3 ). BTW, I'm not using this setup to access raid data from both machines simultaneously. There is Veritas Cluster Server monitoring... (1 Reply)
Discussion started by: shibz
1 Replies

2. UNIX Benchmarks

Sun E250 / 512MB Ram

============================================================== BYTE UNIX Benchmarks (Version 3.11) System -- SunOS xxxxx 5.8 Generic_108528-13 sun4u sparc SUNW,Ultra-250 Start Benchmark Run: Sun Jan 11 19:47:12 EST 2004 1 interactive users. Dhrystone 2 without register variables ... (0 Replies)
Discussion started by: kduffin
0 Replies

3. Solaris

SUN E250 Console connectivity

Hi, I have cisco console cable. One end of the cable is DB9 connector and the other end is RJ45 connector. I would like to use this cable to connect to my SUN E250 system from my pc so that I can access the SUn console directly. I would like to know whether it is possible and also on which... (5 Replies)
Discussion started by: RajaRC
5 Replies

4. Solaris

E250 - need to access it

Hi, We have an E250 which we need to access to install solaris 10 for a communigate trial. We only have the server itself, no cables or anything and im struggling to gain access. It has a RSC card, that i have learned, but a db25-db9 cable doesn't seem to bring anything up in telnet on... (11 Replies)
Discussion started by: e250user
11 Replies

5. Solaris

SUN E250 Cluster

Hi, I need some help, since I am new to cluster. I am handling a site where I have look after two SUN E250 server. I have been asked to configure Active-Active Clustering on these servers. I would like to know how to configure both the servers for clustering. Below are the things which... (5 Replies)
Discussion started by: RajaRC
5 Replies

6. Solaris

Sun Solaris 9 E250 -- Suggestions For External Hard Drives

Hello, Running a Sun Solaris 9 E250 and need advice or suggestions on what type of external hard disks are compatible and or available. It's an old machine and is due for replacement soon but in the short term need an external hard drive for backup etc as the partner/backup machine has just... (2 Replies)
Discussion started by: KenLynch
2 Replies

7. Solaris

Error LED showing on E250

I've got an old E250 server where a front error LED is showing. I've read through the Sun docs (Sun Enterprise 250 Server Owner's Guide - Sun Microsystems) but it's only the 'General fault' LED (About the Status and Control Panel (Sun Enterprise 250 Server Owner's Guide) - Sun Microsystems)... (2 Replies)
Discussion started by: aussieos
2 Replies

8. Solaris

Sun Solaris Enterprise E250 x64 Help

Hi everybody, my name is Giulia and for me is the fist time in this forum, i hope write in the correct section for my problem. I have a sun solaris server e250 enterprise with sun 5 versionof O.S. Now i wont format all and install new version of solaris, but i don't know the actual corrent... (7 Replies)
Discussion started by: giulia79
7 Replies

9. Solaris

E250 server not getting ok prompt

E250 server only shows banner when powered on i am not getting OK PROMPT . .In morning it was booting with solaris 7 .i am not able to do STOP-A STOP-D .its not excepting STOP-N also. Please help (1 Reply)
Discussion started by: monu94
1 Replies
Module::Packaged(3pm)					User Contributed Perl Documentation				     Module::Packaged(3pm)

NAME
Module::Packaged - Report upon packages of CPAN distributions SYNOPSIS
use Module::Packaged; my $p = Module::Packaged->new(); my $dists = $p->check('Archive-Tar'); # $dists is now: # { # cpan => '1.08', # debian => '1.03', # fedora => '0.22', # freebsd => '1.07', # gentoo => '1.05', # openbsd => '0.22', # suse => '0.23', # } # meaning that Archive-Tar is at version 1.08 on CPAN but only at # version 1.07 on FreeBSD, version 1.05 on Gentoo, version 1.03 on # Debian, version 0.23 on SUSE and version 0.22 on OpenBSD DESCRIPTION
CPAN consists of distributions. However, CPAN is not an isolated system - distributions are also packaged in other places, such as for operating systems. This module reports whether CPAN distributions are packaged for various operating systems, and which version they have. Only CPAN, Debian, Fedora (Core 2), FreeBSD, Gentoo, Mandriva (10.1), OpenBSD (3.6) and SUSE (9.2) are currently supported. I want to support everything else. Patches are welcome. The data is fetched from the net and cached for an hour. METHODS
new() The new() method is a constructor: my $p = Module::Packaged->new(); check() The check() method returns a hash reference. The keys are various distributions, the values the version number included: my $dists = $p->check('Archive-Tar'); COPYRIGHT
Copyright (c) 2003-5 Leon Brocard. All rights reserved. This program is free software; you can redistribute it and/or modify it under the same terms as Perl itself. AUTHOR
Leon Brocard, leon@astray.com perl v5.12.4 2011-09-17 Module::Packaged(3pm)
All times are GMT -4. The time now is 06:57 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy