Sponsored Content
Full Discussion: Backup Tape Restore?
Operating Systems HP-UX Backup Tape Restore? Post 302085301 by rockgeek on Wednesday 16th of August 2006 09:56:32 AM
Old 08-16-2006
any further

did the OP get anywhere with this info? i am having similar problems :-(
 

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

Restore to disk from tape

I have been restoring from tape some old data. I have done quite a few tapes and have had no problems until now. The command I am running is "dd if=/dev/rmt/1hbn bs=1024 | tar -pBxF - ". This is the second tape have have come up with the error "Not enough space". This tape has a couple of... (1 Reply)
Discussion started by: mtoombs
1 Replies

2. AIX

Restore a tape

Hello everyone I have a tape with some information that I got to restore, the tape was made with the fbackup command in a hp box. My question is that I have to restore in a Ibm box, how can I do this ? Thanks in advance (1 Reply)
Discussion started by: lo-lp-kl
1 Replies

3. UNIX for Dummies Questions & Answers

Mounting DLT tape and to backup file to tape

Hi there: I'm new here Can anyone help me: I have DS15 Alpha server : Unix 5.1B Now i need to connect a DLVT VS80 1U Rackmount Tape Drive unit. What is the exact comman to mount the DLTape IV?? How do i make backuo @ copy file to the tape? Thanx to all (0 Replies)
Discussion started by: ayzeayem
0 Replies

4. UNIX for Dummies Questions & Answers

Check backup file size on backup tape

Hi, I performed backup on tape and I want to append more files to my previous backup on the same backup tape. But before I do that I need to know the backup file size of the first backup I performed so that I know the available size on the backup tape. Can someone help me what command I will use... (0 Replies)
Discussion started by: ayhanne
0 Replies

5. SCO

Backup to SCSI Tape Backup aborts

I am trying to make a full backup of my system using the cpio command. The Tape Unit is a SCSI DDS. The process started fine but after about 30 minutes, it just stopped and showed the following message: 1755 Signal 31 - Core dumped Any idea of what is causing this and how to fix it? ... (4 Replies)
Discussion started by: zionpc
4 Replies

6. UNIX for Dummies Questions & Answers

I cannot restore my backup from my exabyte tape drive

Hi All, I have an old Unix system used by a client as a backup server.I installed an Exabyte tape drive and on restarting the server and during POSTs, the system recognizes the tape drive with its scsi id. On running the command devstat -IAF, the system sees the tape drive quite well. When... (1 Reply)
Discussion started by: ezleone
1 Replies

7. Solaris

FLAR Tape Backup/Restore

I have a T2000 server that is JumpStarted with Solaris 10 from the JumpStart server. Host name and IP address is changed after that. Then we backup the server using FLAR to tape: root.damas# date; flarcreate -c -t -n "Sol10_cairo_image" -a "engineering@starsolutions.com" -R / /dev/rmt/0n ;... (2 Replies)
Discussion started by: StarSol
2 Replies

8. Solaris

Solaris 2.6 restore from tape

Hope someone can help me here... I've got to restore an E450 with 300MHz cpus which was running Solaris 2.6 from tape. Regrettably the boot drive has failed. I've access to the first release of Solaris 2.6 CD's and to a set of Solaris 9 CD's. I remember that different E450 CPUs needed different... (1 Reply)
Discussion started by: pamplemousse
1 Replies

9. AIX

Tape backup/restore Date/time

good morning everyone how can i find the tape backup/restore Date/time? (2 Replies)
Discussion started by: Portabello
2 Replies

10. Emergency UNIX and Linux Support

Can't restore my deleted etc from tape

Hi I recently deleted my /etc but I had a backup on tape. I was able to boot the server with a cd-rom and mounted the /c1t0d0s0 which is where the root directory resides. However when I tried to restore the backup with tar xvf /dev/rmt/0n I wasn't successful even though I was able to use the tar... (2 Replies)
Discussion started by: rahmantanko
2 Replies
BTRFS-DEBUG-TREE(8)					      System Manager's Manual					       BTRFS-DEBUG-TREE(8)

NAME
btrfs-debug-tree - dump Btrfs filesystem metadata into stdout. SYNOPSIS
btrfs-debug-tree [options] <device> DESCRIPTION
btrfs-debug-tree is used to dump the whole tree of the given device. This is maybe useful for analyzing filesystem state or inconsistence and has a positive educational effect on understanding the internal structure. device is the device file where the filesystem is stored. Options -e print detailed extents info. -d print info of btrfs device and root tree dirs only. -r print info of roots only. -b <block_num> print info of the specified block only. EXIT CODE
btrfs-debug-tree will return 0 if no error happened. If any problems happened, 1 will be returned. AUTHOR
Written by Shilong Wang and Wenruo Qu. COPYRIGHT
Copyright (C) 2013 Fujitsu, Inc. License GPLv2: GNU GPL version 2 <http://gnu.org/licenses/gpl.html>. This is free software: you are free to change and redistribute it. There is NO WARRANTY, to the extent permitted by law. SEE ALSO
mkfs.btrfs(8) BTRFS-DEBUG-TREE(8)
All times are GMT -4. The time now is 08:20 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy