Sponsored Content
Top Forums UNIX for Dummies Questions & Answers Adding an additional harddrive in solaris 9 Post 302083204 by rhfrommn on Friday 4th of August 2006 04:10:09 PM
Old 08-04-2006
The first thing you need to do is make sure the system is seeing the new drive. On a sparc box you'd use the format command, if you're using Solaris x86 I'm not sure if format is there, you may have a different command.

The new disk will have a name something like c0t1d0. You use the format command to create a partition, I'd recommend making one big partition (probably c0t1d0s0) with all the space for a data disk like you're wanting - obviously you can choose to do it different if you prefer multiple partitions. In the format command you can choose your new disk, then the menus will give you the options you need to format the partition.

Once you have your partition made, do a reconfigure boot with reboot -- -r. Then you'll have a device entry like /dev/c0t1d0s0. Use the mkfs command to make a filesystem on it. After that you'd just mount it with the mount command, and add a line to /etc/vfstab so it is mounted on boot from now on. You probably just want to mount the new drive on /mnt by hand and copy your home directory stuff over first time, then set up /etc/vfstab to mount it on /home once you're done with they copying. You can't have both drives mounted on /home at the same time.

For details of the commands I'm talking about see the manpages for format, mkfs, and mount.

Good luck.
 

8 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

adding additional drive to sco the is xenix

I am taking an old xenix drive and installing it in a recent SCO Build Server. I have gone through the process of running mkdev hd twice since the drive is a SCSI then proceed to run mkdev fs and when I attempt to add one of the shown partitions I get the following: fsck: cannot determine... (1 Reply)
Discussion started by: justenglabs
1 Replies

2. UNIX for Dummies Questions & Answers

How to copy MBR from old harddrive to new harddrive?

How do I copy the master boot record from one harddrive to another or how to install just the MBR? (7 Replies)
Discussion started by: shorty
7 Replies

3. Shell Programming and Scripting

Adding additional column at the end

I have a file like below. The separator between reconds is ">" Each record consists of 2 numbers separated by a space. I want to write an awk script that copies the second number and puts it in the third column. :rolleyes: > 10 0 13 5.92346 16 10.3106 19 13.9672 22 16.9838 25... (5 Replies)
Discussion started by: kristinu
5 Replies

4. Shell Programming and Scripting

Adding additional characters while preserving original text

Hi Forum. I'm struggling on this relatively easy request to add additional 4 0's to an existing text in a file (whenever I see the pattern -# where # represents any number) using sed command while preserving the rest of the text in the files. Original Text: $DBConnection_EDW=SAS2EDW... (5 Replies)
Discussion started by: pchang
5 Replies

5. AIX

Any Additional Steps After Adding New RAM To Sever?

Hi All, We have a server at a client site running AIX 5.3, which we just up the RAM to 32GB, from initially 16GB (if I'm not mistaken). This server is our Application server running J2EE applications on top of Oracle Internet Application Server. Recently we encountered one of the batch jobs... (12 Replies)
Discussion started by: a_sim
12 Replies

6. Solaris

Sun Blade 150 will not boot off harddrive after install of solaris 10

Hello, I cant get my blade box to boot off the harddrive after installing solaris 10.I can get to a root prompt after issuing "boot cdrom -s".I tried booting off disk0 and disk1,but I get "the file just loaded does not seem to be executable".Thanks for any help.:wall: (4 Replies)
Discussion started by: chucky
4 Replies

7. Shell Programming and Scripting

Adding an additional blank field to a file

Hi, I have the following file, I'd like to add an additional blank field to this file This is a tab delimited file, I have tried the same thing on excel, but looking for a unix solution. Here is my input: Country Postal Admin4 StreetBaseName StreetType HUN 2243 Kóka Dózsa György ... (3 Replies)
Discussion started by: ramky79
3 Replies

8. Red Hat

Adding Additional Capacity with megacli

I'm trying to add 6 more hard drives to my RAID array, none of the drives are foreign, they won't be replacing any drives either. I just need to add them to the RAID array. I can't seem to get them added, what am I missing? ---------- Post updated 08-03-12 at 12:28 PM ---------- Previous... (0 Replies)
Discussion started by: eccentricson
0 Replies
SYSTEMD-GPT-AUTO-GENERATOR(8)				    systemd-gpt-auto-generator				     SYSTEMD-GPT-AUTO-GENERATOR(8)

NAME
systemd-gpt-auto-generator - Generator for automatically discovering and mounting root, /home and /srv partitions, as well as discovering and enabling swap partitions, based on GPT partition type GUIDs. SYNOPSIS
/lib/systemd/system-generators/systemd-gpt-auto-generator DESCRIPTION
systemd-gpt-auto-generator is a unit generator that automatically discovers root, /home, /srv and swap partitions and creates mount and swap units for them, based on the partition type GUIDs of GUID partition tables (GPT). It implements the Discoverable Partitions Specification[1]. Note that this generator has no effect on non-GPT systems, or where the directories under the mount points are already non-empty. Also, on systems where the units are explicitly configured (for example, listed in fstab(5)), the units this generator creates are overridden, but additional implicit dependencies might be created. This generator will only look for root partitions on the same physical disk the EFI System Partition (ESP) is located on. It will only look for the other partitions on the same physical disk the root file system is located on. These partitions will not be searched on systems where the root file system is distributed on multiple disks, for example via btrfs RAID. systemd-gpt-auto-generator is useful for centralizing file system configuration in the partition table and making manual configuration in /etc/fstab or suchlike unnecessary. This generator looks for the partitions based on their partition type GUID. The following partition type GUIDs are identified: Table 1. Partition Type GUIDs +-------------------------------------+--------------------------------+--------------------------------------+ |Partition Type GUID | Name | Explanation | +-------------------------------------+--------------------------------+--------------------------------------+ |44479540-f297-41b2-9af7-d131d5f0458a | Root Partition (x86) | On 32-bit x86 systems, the first x86 | | | | root partition on the disk the EFI | | | | ESP is located on is mounted to the | | | | root directory /. | +-------------------------------------+--------------------------------+--------------------------------------+ |4f68bce3-e8cd-4db1-96e7-fbcaf984b709 | Root Partition (x86-64) | On 64-bit x86 systems, the first | | | | x86-64 root partition on the disk | | | | the EFI ESP is located on is mounted | | | | to the root directory /. | +-------------------------------------+--------------------------------+--------------------------------------+ |69dad710-2ce4-4e3c-b16c-21a1d49abed3 | Root Partition (32-bit ARM) | On 32-bit ARM systems, the first ARM | | | | root partition on the disk the EFI | | | | ESP is located on is mounted to the | | | | root directory /. | +-------------------------------------+--------------------------------+--------------------------------------+ |b921b045-1df0-41c3-af44-4c6f280d3fae | Root Partition (64-bit ARM) | On 64-bit ARM systems, the first ARM | | | | root partition on the disk the EFI | | | | ESP is located on is mounted to the | | | | root directory /. | +-------------------------------------+--------------------------------+--------------------------------------+ |993d8d3d-f80e-4225-855a-9daf8ed7ea97 | Root Partition (Itanium/IA-64) | On Itanium systems, the first | | | | Itanium root partition on the disk | | | | the EFI ESP is located on is mounted | | | | to the root directory /. | +-------------------------------------+--------------------------------+--------------------------------------+ |933ac7e1-2eb4-4f13-b844-0e14e2aef915 | Home Partition | The first home partition on the disk | | | | the root partition is located on is | | | | mounted to /home. | +-------------------------------------+--------------------------------+--------------------------------------+ |3b8f8425-20e0-4f3b-907f-1a25a76f98e8 | Server Data Partition | The first server data partition on | | | | the disk the root partition is | | | | located on is mounted to /srv. | +-------------------------------------+--------------------------------+--------------------------------------+ |0657fd6d-a4ab-43c4-84e5-0933c84b4f4f | Swap | All swap partitions located on the | | | | disk the root partition is located | | | | on are enabled. | +-------------------------------------+--------------------------------+--------------------------------------+ |c12a7328-f81f-11d2-ba4b-00a0c93ec93b | EFI System Partition (ESP) | The first ESP located on the disk | | | | the root partition is located on is | | | | mounted to /boot or /efi, see below. | +-------------------------------------+--------------------------------+--------------------------------------+ The /home and /srv partitions may be encrypted in LUKS format. In this case, a device mapper device is set up under the names /dev/mapper/home and /dev/mapper/srv. Note that this might create conflicts if the same partition is listed in /etc/crypttab with a different device mapper device name. Mount and automount units for the EFI System Partition (ESP) are generated on EFI systems. The ESP is mounted to /boot, unless a mount point directory /efi exists, in which case it is mounted there. Since this generator creates an automount unit, the mount will only be activated on-demand, when accessed. On systems where /boot (or /efi if it exists) is an explicitly configured mount (for example, listed in fstab(5)) or where the /boot (or /efi) mount point is non-empty, no mount units are generated. When using this generator in conjunction with btrfs file systems, make sure to set the correct default subvolumes on them, using btrfs subvolume set-default. systemd-gpt-auto-generator implements systemd.generator(7). SEE ALSO
systemd(1), systemd.mount(5), systemd.swap(5), systemd-fstab-generator(8), systemd-cryptsetup@.service(8), cryptsetup(8), fstab(5), btrfs(8) NOTES
1. Discoverable Partitions Specification https://www.freedesktop.org/wiki/Specifications/DiscoverablePartitionsSpec/ systemd 237 SYSTEMD-GPT-AUTO-GENERATOR(8)
All times are GMT -4. The time now is 05:33 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy