Check the processor bits Post: 302082311

8 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Changing 24 bits to 8 bits display

Hello all, I was wondering if anyone can tell me how to change 24 bits depth display to 8 bits depth display for Sun Ultra1, running Solaris 8? THANKS in advance. I think that the command is ffbconfig, but it has nothing about depth.

2. AIX

LPAR processor/virtual processor settings

Question is on setting of Physical and Virtual processors for LPARs to make proper use of virtualization capabilities. Environment is a 8-way p570 with 4 LPARs. lparVIO1 and lparVIO2: AIX 5300-04-01 Mode/Type= Shared-SMT/Capped Minimum Processors= 0.10 Desired Processors= 0.50 Maximum...

3. UNIX for Dummies Questions & Answers

Processor bits

Hi friends pls let me know how to find sun processor is 32 bits or 64 bits through command line. thanks

4. UNIX for Dummies Questions & Answers

32 bits procesaor with 64 bits Solaris

people i have a problem i have a 32 bits sparc processor, and solaris 64 bits processor, i install a oracle data base 64 bits, but my oracle will not run because my processor is from 32 bits this is ok??, i know if i have x86 i cannot install a 64 bits operatin system in a 32 bits processor. ...

5. Solaris

Check Solaris Zones Processor & Memory allocations

Hi, I am a newbee in the solaris administration. My question is how to 1. Check the total CPU and memory of a global zone. 2. Check the allocated CPU and memory for each of the residing non-global zones. I have already tried prtconf which gives the following output /usr/sbin/prtconf...

6. What is on Your Mind?

Place Bits & Win Bits!!! - 17th Annual Satellite Awards

Ten movies have been nominated as best motion picture by the International Press Academy, presentation of the 2012 Satellite Awards will be held on 16th December at Los Angeles, CA. Place your bits here on one of the below nominated movie of your choice:- Argo ...

7. UNIX for Advanced & Expert Users

How to check number of threads running per processor in Linux machine?

I have a machine which has 32 processor but i am really not sure how many threads are running. It has hyperthreading enabled. Is there a way i can find that all 32 processors are being used and how many threads are there in my linux box. Its a 64 bit processor. I am having very high load average...

8. Solaris

Solaris installed Physical Processor ..how to check?

I would like to know how to identify the installed "Physical Processor" .here is the output #psrinfo -pv of from 2 systems : - System 1 The physical processor has 8 virtual processors (0-7) SPARC-T4 (chipid 0, clock 2848 MHz) -System 2 The physical processor has 8 virtual...

LEARN ABOUT OSF1

offline

psradm(8)						      System Manager's Manual							 psradm(8)

NAME

       psradm, offline, online - Stops and starts processors in a multiprocessor system

SYNOPSIS

       /usr/sbin/psradm -f  [-v] [[-a] [processor_id...]]

       /usr/sbin/psradm -n  [-v] [[-a] [processor_id...]]

       /usr/sbin/online [-v] [processor_id...]

       /usr/sbin/offline [-v] [processor_id...]

OPTIONS

       The following options apply only to the psradm command: Specifies that all the processors except the master processor be put off line or on
       line.  Puts the specified processor off line.  Puts the specified processor on line.

       The following option applies to all forms of the command: Displays a message about the status of the operation performed on each processor.

DESCRIPTION

       On a multiprocessor system, the psradm command puts one or more processors off line (stops a processor) or on line (starts a processor).

       The processor_id variable specifies an integer that uniquely identifies a processor.  Use the psrinfo command to display processor  identi-
       fication numbers.

       The  offline  command puts one or more processors off line (stops a processor).	If no processors are specified, all processors that are on
       line are stopped except the master processor.

       The online command puts one or more processors on line (starts a processor).  If no processors are specified, all processors that  are  off
       line are started.

       Note that you cannot use these commands to start or stop the master processor in a multiprocessor system.

       You must be the root user to use this command.

       The /var/adm/wtmp file contains information about successful processor state transitions.

RESTRICTION

       Do not use the psradm command to disable CPUs when benchmarking performance, because the command does not provide an accurate reflection of
       the performance of a system that actually has fewer CPUs.  Accurate performance results are obtained only when you disable the CPUs at  the
       SRM console command level.

EXAMPLES

       The  following command puts processors 2 and 3 off line: # psradm -f 2 3 The following command puts all the processors on line: # psradm -n
       -a The following command puts all processors on line: # online -v

FILES

SEE ALSO

       Commands: pset_info(1), psrinfo(1)

       Files: processor_sets(4)

																	 psradm(8)