Seems to be a problem of routing. Perhaps you had the default route through en0.
Notice both interfaces are in the same network.
Post the output of
after and before pulling the cable, and let's see.
Regards.
Hello
am asking for your help on printer issues.
i wanted to change the current printer we have now, basically bec we needed a more durable one. so recently i have a product demo, but its driver is not present in UNIX. i will be using the same network printer name but different model.... (0 Replies)
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Hi All,
This is regarding problem with two servers...
EX:- server1(HP) is not able to connect with proxy server server2(SUN BOX)
But we can able to login.... server1 is not able to pickup any data from the proxy server...
checked in the sunbox...
# ping bdhp5050
server1 is alive
... (1 Reply)
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
I have AIX 5.3 OS. After issuing the print command, the printer state immediately goes down. I have checked the /etc/qconfig flle, resatrted the qdaemon but again same problem is occuring. I am using HP 5100 connected to jetdirect.
what is the problem and it's solution? (4 Replies)
Folks;
I have 2 SUSE servers (192.168.157.100 & 192.168.157.101) both are similar and has the same gateway 192.168.157.1
I can connect to the second one from my PC just fine (192.168.157.101).
The problem is i couldn't connect to the first one using SSH even after i disabled the firewall. when i... (3 Replies)
hi all, i manage a network of 120 windows xp systems and my gateway run on centos 4.6 i actually config the linux gateway my self and i config iptable rules as well.until now, all has been fine but the problem now is that amunable to browse the network using my network places from some of the... (1 Reply)
Dear ALL.
I installed AIX OS on customer sites.
but Only one site is too slow when I connected telnet, ftp..
Ping is too fast. but telnet and FTP is not connected..
of course i check the configuration file on aix but it's normal.
Do any Idea??
thanks in advance.
- Jun - (3 Replies)
Hi everbody;
I have 2 p520 machines and created a vio server for each one (vio01 - vio02). I created 3 AIX 5.3 lpars on vio02 and 3 AIX 6.1 lpars on vio01. The problem is when 2 lpars are activated, i can ping gateway from both lpars and vio; but when i activate 3rd lpar, network downs and none of... (2 Replies)
This is a LPAR that i created earlier.
I want to set an IP address to en0 but it failed.
Command: failed stdout: yes stderr: no
Before command completion, additional instructions may appear below.
en0
devdbm01
inet0 changed
Method error (/usr/lib/methods/chgif):
... (8 Replies)
Discussion started by: wingcross
8 Replies
LEARN ABOUT DEBIAN
dnroute
DNROUTE(8) System Manager's Manual DNROUTE(8)NAME
dnroute - DECnet Routing Daemon
SYNOPSIS
dnroute [options]
Options:
[-dvV2Dtnhr]
DESCRIPTION
dnroute is a daemon that manages the DECnet routing tables to provide a simple
but probably useful routing policy.
dnroute listens for incoming routing messages and adds routes in the kernel for non-local areas that it sees. Routes will be modifed
according to these messages so that the lowest cost route that is up will always be used. Routes to locally accessible nodes (it those in
the neighbour table) will also be added. If you want to keep manual control of the route to a particular area, then add a line into
dnroute.conf. eg:
manual 26
will disable dnroute's setting of routing tables for that area. dnetinfo will still show the route that would have been set with (M) on the
line to show it has been overidden.
To implement its routing policies dnroute assumes that all interfaces on the system have a cost of 4. To change this add lines in
/etc/dnroute.conf for each of the interfaces you need to change. eg
eth0 6
eth1 8
tap0 10
A script called dnetinfo is provided that gets the routing information from dnroute and displays it on stdout in a format similar to the
VMS command SHOW NET/OLD.
OPTIONS -d Don't fork and run the background. Use this for debugging.
-v Verbose. Log route changes to syslog.
-D Debug log. Writes debugging information to stderr. Only useful with -d.
-h -? Displays help for using the command.
-r Send DECnet routing messages showing the state of local nodes.
-2 Send DECnet level 2 (area) routing messages. Implies -r.
-t <secs>
Timer to send routing messages on. Defaults to 15 seconds.
-n Do not set up routes or send routing messages, just monitor the network. Useful for testing.
-V Show the version of dnroute.
SEE ALSO dnetd.conf(5), ip(8)DECnet utilities March 30 2006 DNROUTE(8)