E250 - need to access it Post: 302080658

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Need help to access/mount so to access folder/files on a Remote System using Linux OS

Hi I need to access files from a specific folder of a Linux system from an another Linux System Remotely. I know how to, Export a folder on One SCO System & can access the same by using Import via., NFS in the Sco Unix SVR4 System using the scoadmin utility. Also, I know to use mount -t ...

2. UNIX for Advanced & Expert Users

Raid A1000 with E450 and E250.

Hi, I'm facing problem in connecting a Raid A1000 to E250 and E450. ( Both machines with Solaris 2.6 OS and patched, with different scsi-initiator-ids - 7 & 3 ). BTW, I'm not using this setup to access raid data from both machines simultaneously. There is Veritas Cluster Server monitoring...

3. UNIX Benchmarks

Sun E250 / 512MB Ram

============================================================== BYTE UNIX Benchmarks (Version 3.11) System -- SunOS xxxxx 5.8 Generic_108528-13 sun4u sparc SUNW,Ultra-250 Start Benchmark Run: Sun Jan 11 19:47:12 EST 2004 1 interactive users. Dhrystone 2 without register variables ...

4. Solaris

SUN E250 Console connectivity

Hi, I have cisco console cable. One end of the cable is DB9 connector and the other end is RJ45 connector. I would like to use this cable to connect to my SUN E250 system from my pc so that I can access the SUn console directly. I would like to know whether it is possible and also on which...

5. Gentoo

Uses for a Sun e250?

We are retiring a Sun e250 at work, and I wondered if I could put it to any good use. Will I have any problems loading Linux as opposed to Solaris? Should I use any particular flavor of Linux that might be more Sun friendly? Assuming I manage to load Linux on this server, then what? Will it be...

6. Solaris

SUN E250 Cluster

Hi, I need some help, since I am new to cluster. I am handling a site where I have look after two SUN E250 server. I have been asked to configure Active-Active Clustering on these servers. I would like to know how to configure both the servers for clustering. Below are the things which...

7. Solaris

Sun Solaris 9 E250 -- Suggestions For External Hard Drives

Hello, Running a Sun Solaris 9 E250 and need advice or suggestions on what type of external hard disks are compatible and or available. It's an old machine and is due for replacement soon but in the short term need an external hard drive for backup etc as the partner/backup machine has just...

8. Solaris

Error LED showing on E250

I've got an old E250 server where a front error LED is showing. I've read through the Sun docs (Sun Enterprise 250 Server Owner's Guide - Sun Microsystems) but it's only the 'General fault' LED (About the Status and Control Panel (Sun Enterprise 250 Server Owner's Guide) - Sun Microsystems)...

9. Solaris

Sun Solaris Enterprise E250 x64 Help

Hi everybody, my name is Giulia and for me is the fist time in this forum, i hope write in the correct section for my problem. I have a sun solaris server e250 enterprise with sun 5 versionof O.S. Now i wont format all and install new version of solaris, but i don't know the actual corrent...

10. Solaris

E250 server not getting ok prompt

E250 server only shows banner when powered on i am not getting OK PROMPT . .In morning it was booting with solaris 7 .i am not able to do STOP-A STOP-D .its not excepting STOP-N also. Please help

LEARN ABOUT NETBSD

iy

IY(4)							   BSD Kernel Interfaces Manual 						     IY(4)

NAME

     iy -- Intel EtherExpress PRO/10 Ethernet driver (Intel i82595)

SYNOPSIS

     iy0 at isa? port {port} irq ?

DESCRIPTION

     The iy device driver supports the EtherExpress PRO/10 card, and might support other ISA cards using the same chip.

MEDIA SELECTION

     The different models of the supported boards come with some subset of RJ-45, BNC and AUI connectors.  Supported media include:

	   AUI/DIX     Standard 15 pin connector

	   10Base2     BNC, also known as thin-net

	   10BaseT     UTP, also known as twisted pair

     The default port to use is the port the card autodetects at ifconfig up time.  To choose an alternative port, an explicit medium can be spec-
     ified to ifconfig(8) or in your ifconfig.iy? file.

NOTES

     The EtherExpress PRO card has no jumpers to set the address.  Intel supplies software to set the address of the card in software.	You have
     to hardwire this address in your kernel configuration file.

SEE ALSO

     ed(4), eg(4), el(4), ep(4), intro(4), ix(4), le(4), ifconfig(8)

STANDARDS

     are great.  There's so many to choose from.

BSD
								   May 22, 1996 							       BSD