07-19-2006
Suggest you remove the logical drives and recreate them.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
hi,
1) is logical partition the same as physical partition except that one is physical and the other is logical?
2) then it must a one to one ratio? (3 Replies)
Discussion started by: yls177
3 Replies
2. IP Networking
Hi guys,
I have set up multiple virtual FTP servers on a server through one physical NIC. I believe there are to ways; setting logical or alias ip's. I would like to know what is the difference between setting up a logical ip or setting up an alias ip to a physical network interface? Some links to... (5 Replies)
Discussion started by: zaff
5 Replies
3. AIX
hello
I have a volume group of 737 Go (EMC)
To add 250 Go, i split the 250 Go to 2*125
No problem to add in the volum group, but when i want to increase the size of the logical volume, i have the message :
0516-787 extendlv: Maximum allocation for logical volume simdatabaselv
is... (3 Replies)
Discussion started by: pascalbout
3 Replies
4. AIX
I would like to know how to identify which file a logical partition relates too.
Operating System = AIX
oslevel -s = 5300-04-CSP
I've identified a logical volume that continually runs at 100% tm_acct from iostat.
I've run lvmstat -l and identified the logical partition 590, being the... (1 Reply)
Discussion started by: garry
1 Replies
5. AIX
Hi,
What is the typical AIX procedure for creating a logical volume from CLI.
I have mostly worked on HPUX so far and on which the typica steps are:
1: pvcreate -f /dev/rdsk/<mydisk>
2: mkdir /dev/<myvg>
3: mknod /dev/<myvg>/group C 64 <0x030000>
4: vgcreate /dev/<myvg>... (2 Replies)
Discussion started by: amit4g
2 Replies
6. Solaris
Hi All,
I have managed to install and configure a Solaris x86 server, the problem I have now is that whilst setting it up, I left a 30GB logical partition for the Oracle database server that I will later have on the system, the problem now is that I have not formatted the drive during... (18 Replies)
Discussion started by: platforminc
18 Replies
7. Solaris
I have created a pool named earthpool using zpool command. Later I created a file system named earth using zfs command. I changed the mountpoint of earth (file system) using
zfs set mountpoint=/earth earthpool/earth.
Where /earth is a directory created in root using mkdir.
Now, I have a... (8 Replies)
Discussion started by: bharu_sri
8 Replies
8. UNIX for Advanced & Expert Users
I needed to create a un-formatted partition of X MB on a disk dont want it from GUI but from command line not sure what should be specified for fdisk (4 Replies)
Discussion started by: dinjo_jo
4 Replies
9. HP-UX
Hi to all,
I am brand new to HP-UX but am quite familiar with Linux systems (Red Hat, Ubuntu etc..)
I've just taken over a new HP-UX box and trying to work out how to create a logical volume.
As well as creating the volume, which I am sure is very easy I need to create a special character... (6 Replies)
Discussion started by: jamie2teach
6 Replies
10. Solaris
hi all
while formatting hard disk i am getting following error.
Partition 1 ends at 266338338
It must be between 34 and 143374704.
label error: EFI Labels do not support overlapping partitions
Partition 8 overlaps partition 1.
Warning: error writing EFI.
Label failed.
I have formatted the... (2 Replies)
Discussion started by: nikhil kasar
2 Replies
IDA(4) BSD Kernel Interfaces Manual IDA(4)
NAME
ida -- Compaq Intelligent Drive Array Controllers
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device ida
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
ida_load="YES"
DESCRIPTION
The Compaq Intelligent Drive Array (IDA) technology is used to distribute data across an array of hard drives. It unites these hard drives
into one or more high-performance logical drives. The drive array is managed by an array controller.
These controllers have the ability to provide fault tolerance for the connected drives and optionally provide write cache for the logical
drives. It is also possible for an application to access the SCSI bus subsystem directly by using the pass-through interface.
HARDWARE
The following controllers are supported by the ida driver:
o Compaq SMART Array 221
o Compaq Integrated SMART Array Controller
o Compaq SMART Array 4200
o Compaq SMART Array 4250ES
o Compaq SMART 3200 Controller
o Compaq SMART 3100ES Controller
o Compaq SMART-2/DH Controller
o Compaq SMART-2/SL Controller
o Compaq SMART-2/P Controller
o Compaq SMART-2/E Controller
o Compaq SMART Controller
IMPLEMENTATION NOTES
Extreme caution should be exercised when using the pass-through interface. It is possible to interfere with normal system I/O and cause
hangs if pass-through is used to an active device. Pass-through should only be used to a device that is otherwise quiescent.
SEE ALSO
cam(4), pass(4), xpt(4), camcontrol(8)
AUTHORS
The ida driver was written by Jonathan Lemon <jlemon@FreeBSD.org> and Matthew N. Dodd <mdodd@FreeBSD.org>. This manual page was written by
Tom Rhodes <trhodes@FreeBSD.org>.
BSD
August 8, 2004 BSD