07-14-2006
Ok then,
plz define the /dev/hdc -> is it your CDROM?
and how about these 2 :ide0=0x1f0,0x3f6? both drives in 1 ide?
how about the SATA controller - correctly set?
cheers..
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I believe i have most of samba configured right but i get this error each time time try to run it. I was given suggestion that i touch the file, i did, but i still cannot rid myself of this error.
Any suggestions (2 Replies)
Discussion started by: macdonto
2 Replies
2. Linux Benchmarks
Notes:
System Configuration: Dell Computer Corporation PowerEdge 4600 (4 X Intel(R) XEON(TM) CPU 2.00GHz
1988.782 MHz) hyperthreaded
System clock frequency: 99.0827 MHz
Memory size (approximate): 2559 Megabytes
========================= CPUs ========================
CPU # CPU... (0 Replies)
Discussion started by: tnorth
0 Replies
3. Linux Benchmarks
CPU/Speed: Dual PIII 533
Ram: 256Mb PC133
Motherboard: Unknown, Intel Chipset
Cache: 256k on board
Controller: PARC Raid 2/Si, AIC-7880U
Disk: 30Gb RAID 5
Load: 1 user. Clean boot, init 5 but X-Windows not loaded.
Kernel: See Benchmarks.
pgms: gcc 3.2.3
... (2 Replies)
Discussion started by: Garp
2 Replies
4. Solaris
hi, i am trying to install solaris 10 (on 4 cd's downloaded from the sun website) on my dell poweredge 2800 server. 2 xeon processors, 2GB of RAM and 2 NICS, 73 GB SCSI (maxtor ultra320, 3.5 series), i can give more details on request...
the installation crashes when trying to detect the NICS... (0 Replies)
Discussion started by: xinugeek
0 Replies
5. Filesystems, Disks and Memory
Does anybody no how to get around the fact that the Red Hat installation does not see the SCSI hard drives. It lets you manually pick the proper device, but still fails saying no drive detected (or something to that effect). I was going to install windows 2003 Server and use VMware...but again,... (1 Reply)
Discussion started by: Fatflea
1 Replies
6. Programming
Hi,
I have a C++ program to access /dev/mem and retrieve details like Vendor, Manufacturer details of the motherboard. This works fine on all the machines except for on Dell Poweredge 2850,1950... machines.
I receive a 'EFAULT' when I try to access /dev/mem on these servers.
I suspect some... (1 Reply)
Discussion started by: ragisreekanth
1 Replies
7. SCO
I was asked to get a Dell PowerEdge 2600 server, out of warranty, running SCO 3.2v5.06 to perform a full backup. I spent hours researching and preparing a strategy only to fail on-site.
The only device names in /dev for a tape drive were
/dev/xStp0
/dev/xcdt0
/dev/xct0
... (6 Replies)
Discussion started by: ezlarry
6 Replies
8. Programming
Dear Team
I am using DB2 v10 z/os database . Need expert guidance to figure out best way to track table activities ( Ex Delete, Insert,Update )
Scenario
We have a table which is critical and many developer/testing team access on daily basis . We had instance where some deleted... (1 Reply)
Discussion started by: Perlbaby
1 Replies
9. UNIX for Beginners Questions & Answers
My server has /var/log/messages with 'init: initLogger main process (608798) terminated with status 1' errors. I researched about the error and also followed the steps from stackexchange :
157059/error-init-ttys0-dev-ttys0-main-process-1612-terminated-with-status-1]linux - ERROR: init: ttyS0... (0 Replies)
Discussion started by: Paras Pandey
0 Replies
TWS(4) BSD Kernel Interfaces Manual TWS(4)
NAME
tws -- 3ware 9750 SATA+SAS 6Gb/s RAID controller card driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device tws
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
tws_load="YES"
DESCRIPTION
The tws driver provides support for LSI's 3ware 9750 SATA+SAS 6Gb/s RAID controller cards.
These controllers feature the LSISAS2108 6Gb/s SAS RAID-on-Chip (ROC) and are available in 4- and 8-port configurations, supports RAID levels
0, 1, 5, 6, 10, 50 and single disk, with 96 SATA and/or SAS hard drives and SSDs.
For further hardware information, see http://www.lsi.com/.
HARDWARE
The tws driver supports the following SATA/SAS RAID controller:
o LSI's 3ware SAS 9750 series
LOADER TUNABLES
Tunables can be set at the loader(8) prompt before booting the kernel or stored in loader.conf(5).
hw.tws.cam_depth The maximum queued CAM SIM requests for one controller. The default value is 256.
hw.tws.enable_msi This tunable enables MSI support on the controller if set to a non-zero value. The default value is 0.
hw.tws.queue_depth The maximum queued requests for one controller.
hw.tws.use_32bit_sgls Limit the driver to use only 32-bit SG elements regardless whether the operating system is running in 64-bit mode.
The default value is 0.
FILES
/dev/da? array/logical disk interface
/dev/tws? management interface
DIAGNOSTICS
Whenever the driver encounters a command failure, it prints out an error code in the format: "ERROR: (<error source>: <error code>):", fol-
lowed by a text description of the error. There are other error messages and warnings that the driver prints out, depending on the kinds of
errors that it encounters. If the driver is compiled with TWS_DEBUG defined, it prints out a whole bunch of debug messages.
SEE ALSO
da(4), scsi(4)
AUTHORS
The tws driver was written by Manjunath Ranganathaiah for LSI and this manual page was written by Xin LI <delphij@FreeBSD.org> for iXsystems,
Inc.
BSD
October 4, 2011 BSD