07-12-2006
hello,
do you really need to pass a kernel parameter??
cheers.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I believe i have most of samba configured right but i get this error each time time try to run it. I was given suggestion that i touch the file, i did, but i still cannot rid myself of this error.
Any suggestions (2 Replies)
Discussion started by: macdonto
2 Replies
2. Linux Benchmarks
Notes:
System Configuration: Dell Computer Corporation PowerEdge 4600 (4 X Intel(R) XEON(TM) CPU 2.00GHz
1988.782 MHz) hyperthreaded
System clock frequency: 99.0827 MHz
Memory size (approximate): 2559 Megabytes
========================= CPUs ========================
CPU # CPU... (0 Replies)
Discussion started by: tnorth
0 Replies
3. Linux Benchmarks
CPU/Speed: Dual PIII 533
Ram: 256Mb PC133
Motherboard: Unknown, Intel Chipset
Cache: 256k on board
Controller: PARC Raid 2/Si, AIC-7880U
Disk: 30Gb RAID 5
Load: 1 user. Clean boot, init 5 but X-Windows not loaded.
Kernel: See Benchmarks.
pgms: gcc 3.2.3
... (2 Replies)
Discussion started by: Garp
2 Replies
4. Solaris
hi, i am trying to install solaris 10 (on 4 cd's downloaded from the sun website) on my dell poweredge 2800 server. 2 xeon processors, 2GB of RAM and 2 NICS, 73 GB SCSI (maxtor ultra320, 3.5 series), i can give more details on request...
the installation crashes when trying to detect the NICS... (0 Replies)
Discussion started by: xinugeek
0 Replies
5. Filesystems, Disks and Memory
Does anybody no how to get around the fact that the Red Hat installation does not see the SCSI hard drives. It lets you manually pick the proper device, but still fails saying no drive detected (or something to that effect). I was going to install windows 2003 Server and use VMware...but again,... (1 Reply)
Discussion started by: Fatflea
1 Replies
6. Programming
Hi,
I have a C++ program to access /dev/mem and retrieve details like Vendor, Manufacturer details of the motherboard. This works fine on all the machines except for on Dell Poweredge 2850,1950... machines.
I receive a 'EFAULT' when I try to access /dev/mem on these servers.
I suspect some... (1 Reply)
Discussion started by: ragisreekanth
1 Replies
7. SCO
I was asked to get a Dell PowerEdge 2600 server, out of warranty, running SCO 3.2v5.06 to perform a full backup. I spent hours researching and preparing a strategy only to fail on-site.
The only device names in /dev for a tape drive were
/dev/xStp0
/dev/xcdt0
/dev/xct0
... (6 Replies)
Discussion started by: ezlarry
6 Replies
8. Programming
Dear Team
I am using DB2 v10 z/os database . Need expert guidance to figure out best way to track table activities ( Ex Delete, Insert,Update )
Scenario
We have a table which is critical and many developer/testing team access on daily basis . We had instance where some deleted... (1 Reply)
Discussion started by: Perlbaby
1 Replies
9. UNIX for Beginners Questions & Answers
My server has /var/log/messages with 'init: initLogger main process (608798) terminated with status 1' errors. I researched about the error and also followed the steps from stackexchange :
157059/error-init-ttys0-dev-ttys0-main-process-1612-terminated-with-status-1]linux - ERROR: init: ttyS0... (0 Replies)
Discussion started by: Paras Pandey
0 Replies
HD(4) Linux Programmer's Manual HD(4)
NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO
chown(1), mknod(1), sd(4), mount(8)
COLOPHON
This page is part of release 3.53 of the Linux man-pages project. A description of the project, and information about reporting bugs, can
be found at http://www.kernel.org/doc/man-pages/.
Linux 1992-12-17 HD(4)