Installing RedHat 8.0 onto Dell PowerEdge SC1425 - hdc: status error: status = 0x58 Post: 302079732

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Couldn't open status file /var/samba/STATUS.LCK

I believe i have most of samba configured right but i get this error each time time try to run it. I was given suggestion that i touch the file, i did, but i still cannot rid myself of this error. Any suggestions

2. Linux Benchmarks

Dell Dual Xeon PowerEdge 4600

Notes: System Configuration: Dell Computer Corporation PowerEdge 4600 (4 X Intel(R) XEON(TM) CPU 2.00GHz 1988.782 MHz) hyperthreaded System clock frequency: 99.0827 MHz Memory size (approximate): 2559 Megabytes ========================= CPUs ======================== CPU # CPU...

3. Linux Benchmarks

Dell Poweredge 2400 / 533

CPU/Speed: Dual PIII 533 Ram: 256Mb PC133 Motherboard: Unknown, Intel Chipset Cache: 256k on board Controller: PARC Raid 2/Si, AIC-7880U Disk: 30Gb RAID 5 Load: 1 user. Clean boot, init 5 but X-Windows not loaded. Kernel: See Benchmarks. pgms: gcc 3.2.3 ...

4. Solaris

Installing Solaris 10 on Dell PowerEdge 2800

hi, i am trying to install solaris 10 (on 4 cd's downloaded from the sun website) on my dell poweredge 2800 server. 2 xeon processors, 2GB of RAM and 2 NICS, 73 GB SCSI (maxtor ultra320, 3.5 series), i can give more details on request... the installation crashes when trying to detect the NICS...

5. Filesystems, Disks and Memory

Linux and Dell 1500sc Poweredge Server

Does anybody no how to get around the fact that the Red Hat installation does not see the SCSI hard drives. It lets you manually pick the proper device, but still fails saying no drive detected (or something to that effect). I was going to install windows 2003 Server and use VMware...but again,...

6. Programming

/dev/mem on Dell Poweredge

Hi, I have a C++ program to access /dev/mem and retrieve details like Vendor, Manufacturer details of the motherboard. This works fine on all the machines except for on Dell Poweredge 2850,1950... machines. I receive a 'EFAULT' when I try to access /dev/mem on these servers. I suspect some...

7. SCO

Dell PowerEdge 2600 tape backup

I was asked to get a Dell PowerEdge 2600 server, out of warranty, running SCO 3.2v5.06 to perform a full backup. I spent hours researching and preparing a strategy only to fail on-site. The only device names in /dev for a tape drive were /dev/xStp0 /dev/xcdt0 /dev/xct0 ...

8. Programming

How to track table status delete/update/insert status in DB2 V10 z/os?

Dear Team I am using DB2 v10 z/os database . Need expert guidance to figure out best way to track table activities ( Ex Delete, Insert,Update ) Scenario We have a table which is critical and many developer/testing team access on daily basis . We had instance where some deleted...

9. UNIX for Beginners Questions & Answers

Redhat Virtualization EN error : InitLogger main process terminated with status 1

My server has /var/log/messages with 'init: initLogger main process (608798) terminated with status 1' errors. I researched about the error and also followed the steps from stackexchange : 157059/error-init-ttys0-dev-ttys0-main-process-1612-terminated-with-status-1]linux - ERROR: init: ttyS0...

LEARN ABOUT HPUX

sysdef

sysdef(1M)																sysdef(1M)

NAME

       sysdef - display system definition

SYNOPSIS

       [kernel [master]]

DESCRIPTION

       Note: will not be supported in future releases of HP-UX (refer to section below).  So users are advised to use the kctune(1M) utility which
       provides additional information on kernel tunable parameters.

       The command analyzes the currently running system and reports on its tunable configuration parameters.  kernel and master are not used, but
       can be specified for standards compliance.

       For each configuration parameter, the following information is printed:

	      The name and description of the parameter.

	      The current value of the parameter.

	      The value of the parameter at boot time, if different from the
			     current value.

	      The minimum allowed value of the parameter, if any.

	      The maximum allowed value of the parameter, if any.

	      Where appropriate, the units by which the parameter is measured.

	      Flags that further describe the parameter.  The following flag
			     is defined:

				  Parameter can be modified without rebooting.

WARNINGS

       Users  of must not rely on the exact field widths and spacing of its output, as these will vary depending on the system, the release of HP-
       UX, and the data to be displayed.

       is provided for compatibility purposes only and is no longer maintained since being marked for obsolescence in a future HP-UX release.  The
       output from is known to be incorrect when reporting values for some tunable parameters such as and

SEE ALSO

       kctune(1M).

								  TO BE OBSOLETED							sysdef(1M)