I believe i have most of samba configured right but i get this error each time time try to run it. I was given suggestion that i touch the file, i did, but i still cannot rid myself of this error.
Any suggestions (2 Replies)
hi, i am trying to install solaris 10 (on 4 cd's downloaded from the sun website) on my dell poweredge 2800 server. 2 xeon processors, 2GB of RAM and 2 NICS, 73 GB SCSI (maxtor ultra320, 3.5 series), i can give more details on request...
the installation crashes when trying to detect the NICS... (0 Replies)
Does anybody no how to get around the fact that the Red Hat installation does not see the SCSI hard drives. It lets you manually pick the proper device, but still fails saying no drive detected (or something to that effect). I was going to install windows 2003 Server and use VMware...but again,... (1 Reply)
Hi,
I have a C++ program to access /dev/mem and retrieve details like Vendor, Manufacturer details of the motherboard. This works fine on all the machines except for on Dell Poweredge 2850,1950... machines.
I receive a 'EFAULT' when I try to access /dev/mem on these servers.
I suspect some... (1 Reply)
I was asked to get a Dell PowerEdge 2600 server, out of warranty, running SCO 3.2v5.06 to perform a full backup. I spent hours researching and preparing a strategy only to fail on-site.
The only device names in /dev for a tape drive were
/dev/xStp0
/dev/xcdt0
/dev/xct0
... (6 Replies)
Dear Team
I am using DB2 v10 z/os database . Need expert guidance to figure out best way to track table activities ( Ex Delete, Insert,Update )
Scenario
We have a table which is critical and many developer/testing team access on daily basis . We had instance where some deleted... (1 Reply)
My server has /var/log/messages with 'init: initLogger main process (608798) terminated with status 1' errors. I researched about the error and also followed the steps from stackexchange :
157059/error-init-ttys0-dev-ttys0-main-process-1612-terminated-with-status-1]linux - ERROR: init: ttyS0... (0 Replies)
Discussion started by: Paras Pandey
0 Replies
LEARN ABOUT PLAN9
vga
VGA(3) Library Functions Manual VGA(3)NAME
vga - VGA controller device
SYNOPSIS
bind #v /dev
/dev/vgactl
/dev/vgaiob
/dev/vgaiow
/dev/vgaiol
DESCRIPTION
The VGA device allows configuration of a graphics controller on a PC. Vgactl allows control over higher-level settings such as display
height, width, depth, controller and hardware-cursor type. Vgaiob, vgaiow and vgaiol allow control over individual 8-bit, 16-bit and
32-bit x86 I/O-ports respectively, such as those used to implement configuration and setup registers on a VGA controller card. These func-
tions are normally carried out by vga(8).
Writes to vgactl are of the form `attribute value'. Valid attributes are
size value is 'XxYxZ' , where X, Y and Z are numbers that tell the kernel the width and height of the screen in pixels and the number of
bits per pixel.
type tells the kernel which type of controller is being used, mainly to enable the correct code for display-memory bank switching at res-
olutions greater than 640x480x1. The names vga, clgd542x, et4000, mach32, and s3 are supported for value.
Note that this list does not indicate the full set of VGA chips supported. For example, s3 includes the 86C801/5, 86C928, Vision864,
and Vision964. It is the job of vga(8) to recognize which particular chip is being used and to initialize it appropriately.
hwgc tells the kernel to use a particular type of hardware graphics cursor. Bt485hwgc, et4000hwgc, s3hwgc and tvp3020hwgc, are currently
recognized values. A value of off reverts to using the software cursor.
Reading vgactl returns the current settings, one per line.
EXAMPLES
The following reverts to using the software graphics cursor
echo -n 'hwgc off' >/dev/vgactl
Sample code to read an x86 8-bit I/O port
uchar
inportb(long port)
{
uchar data;
if(iobfd == -1)
iobfd = open("#v/vgaiob", ORDWR);
seek(iobfd, port, 0);
if(read(iobfd, &data, sizeof(data)) != sizeof(data))
error("inportb(0x%4.4x): %r0, port);
return data;
}
SOURCE
/sys/src/9/pc/devvga.c
SEE ALSO vga(8)BUGS
There should be some restriction on the range of valid ports.
There should be support for the hardware graphics cursor on the clgd54[23]x VGA controller chips.
The hardware graphics cursor on the et4000 does not work in 2x8-bit mode.
VGA(3)