However, since installation, the system no longer boots. I've tried appending the above parameters to the kernel line in grub, but is still doesn't boot.
It starts to boot, and everything looks fine, until it tries to remount the root fs in read/write mode, at which point it appears to hang.
There are several messages on screen, all of which are normal, except two instances of the following:
Code:
hdc: status error: status = 0x58
NOTE: For some reason, the two hard drives were picked up as hdc and hde, but it seemed to install OK.
If i boot up into rescue mode on the installation CD, i can mount the drives fine, and chroot into my newly built system, but it just won't boot up by itself.
I believe i have most of samba configured right but i get this error each time time try to run it. I was given suggestion that i touch the file, i did, but i still cannot rid myself of this error.
Any suggestions (2 Replies)
hi, i am trying to install solaris 10 (on 4 cd's downloaded from the sun website) on my dell poweredge 2800 server. 2 xeon processors, 2GB of RAM and 2 NICS, 73 GB SCSI (maxtor ultra320, 3.5 series), i can give more details on request...
the installation crashes when trying to detect the NICS... (0 Replies)
Does anybody no how to get around the fact that the Red Hat installation does not see the SCSI hard drives. It lets you manually pick the proper device, but still fails saying no drive detected (or something to that effect). I was going to install windows 2003 Server and use VMware...but again,... (1 Reply)
Hi,
I have a C++ program to access /dev/mem and retrieve details like Vendor, Manufacturer details of the motherboard. This works fine on all the machines except for on Dell Poweredge 2850,1950... machines.
I receive a 'EFAULT' when I try to access /dev/mem on these servers.
I suspect some... (1 Reply)
I was asked to get a Dell PowerEdge 2600 server, out of warranty, running SCO 3.2v5.06 to perform a full backup. I spent hours researching and preparing a strategy only to fail on-site.
The only device names in /dev for a tape drive were
/dev/xStp0
/dev/xcdt0
/dev/xct0
... (6 Replies)
Dear Team
I am using DB2 v10 z/os database . Need expert guidance to figure out best way to track table activities ( Ex Delete, Insert,Update )
Scenario
We have a table which is critical and many developer/testing team access on daily basis . We had instance where some deleted... (1 Reply)
My server has /var/log/messages with 'init: initLogger main process (608798) terminated with status 1' errors. I researched about the error and also followed the steps from stackexchange :
157059/error-init-ttys0-dev-ttys0-main-process-1612-terminated-with-status-1]linux - ERROR: init: ttyS0... (0 Replies)
Discussion started by: Paras Pandey
0 Replies
LEARN ABOUT SUNOS
installgrub
installgrub(1M)installgrub(1M)NAME
installgrub - install GRUB in a disk partition or a floppy
SYNOPSIS
/sbin/installgrub [-fm] stage1 stage2 raw-device
The installgrub command is an -only program. GRUB stands for GRand Unified Bootloader.
installgrub installs GRUB stage 1 and stage 2 files on the boot area of a disk partition. If you specify the -m option, installgrub
installs the stage 1 file on the master boot sector of the disk.
The installgrub command accepts the following options:
-f
Suppresses interaction when overwriting the master boot sector.
-m
Installs GRUB stage1 on the master boot sector interactively.
The installgrub command accepts the following operands:
stage1
The name of the GRUB stage 1 file.
stage2
The name of the GRUB stage 2 file.
raw-device
The name of the device onto which GRUB code is to be installed. It must be a character device that is readable and writable. For disk
devices, specify the slice where the GRUB menu file is located. (For Solaris it is the root slice.) For a floppy disk, it is
/dev/rdiskette.
Example 1: Installing GRUB on a Hard Disk Slice
The following command installs GRUB on a system where the root slice is c0d0s0:
example# /sbin/installgrub /boot/grub/stage1
/boot/grub/stage2 /dev/rdsk/c0d0s0
Example 2: Installing GRUB on a Floppy
The following command installs GRUB on a formatted floppy:
example# mount -F pcfs /dev/diskette /mnt
# mkdir -p /mnt/boot/grub
# cp /boot/grub/* /mnt/boot/grub
# umount /mnt
# cd /boot/grub
# /sbin/installgrub stage1 stage2 /dev/rdiskette
/boot/grub
Directory where GRUB files reside.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
boot(1M), fdisk(1M), fmthard(1M), kernel(1M), attributes(5)
Installing GRUB on the master boot sector (-m option) overrides any boot manager currently installed on the machine. The system will always
boot the GRUB in the Solaris partition regardless of which fdisk partition is active.
24 May 2005 installgrub(1M)
07-11-2006
Installing RedHat 8.0 onto Dell PowerEdge SC1425 - hdc: status error: status = 0x58
