However, since installation, the system no longer boots. I've tried appending the above parameters to the kernel line in grub, but is still doesn't boot.
It starts to boot, and everything looks fine, until it tries to remount the root fs in read/write mode, at which point it appears to hang.
There are several messages on screen, all of which are normal, except two instances of the following:
Code:
hdc: status error: status = 0x58
NOTE: For some reason, the two hard drives were picked up as hdc and hde, but it seemed to install OK.
If i boot up into rescue mode on the installation CD, i can mount the drives fine, and chroot into my newly built system, but it just won't boot up by itself.
I believe i have most of samba configured right but i get this error each time time try to run it. I was given suggestion that i touch the file, i did, but i still cannot rid myself of this error.
Any suggestions (2 Replies)
hi, i am trying to install solaris 10 (on 4 cd's downloaded from the sun website) on my dell poweredge 2800 server. 2 xeon processors, 2GB of RAM and 2 NICS, 73 GB SCSI (maxtor ultra320, 3.5 series), i can give more details on request...
the installation crashes when trying to detect the NICS... (0 Replies)
Does anybody no how to get around the fact that the Red Hat installation does not see the SCSI hard drives. It lets you manually pick the proper device, but still fails saying no drive detected (or something to that effect). I was going to install windows 2003 Server and use VMware...but again,... (1 Reply)
Hi,
I have a C++ program to access /dev/mem and retrieve details like Vendor, Manufacturer details of the motherboard. This works fine on all the machines except for on Dell Poweredge 2850,1950... machines.
I receive a 'EFAULT' when I try to access /dev/mem on these servers.
I suspect some... (1 Reply)
I was asked to get a Dell PowerEdge 2600 server, out of warranty, running SCO 3.2v5.06 to perform a full backup. I spent hours researching and preparing a strategy only to fail on-site.
The only device names in /dev for a tape drive were
/dev/xStp0
/dev/xcdt0
/dev/xct0
... (6 Replies)
Dear Team
I am using DB2 v10 z/os database . Need expert guidance to figure out best way to track table activities ( Ex Delete, Insert,Update )
Scenario
We have a table which is critical and many developer/testing team access on daily basis . We had instance where some deleted... (1 Reply)
My server has /var/log/messages with 'init: initLogger main process (608798) terminated with status 1' errors. I researched about the error and also followed the steps from stackexchange :
157059/error-init-ttys0-dev-ttys0-main-process-1612-terminated-with-status-1]linux - ERROR: init: ttyS0... (0 Replies)
Discussion started by: Paras Pandey
0 Replies
LEARN ABOUT SUSE
halt
HALT(8) Linux System Administrator's Manual HALT(8)NAME
halt, reboot, poweroff - stop the system.
SYNOPSIS
/sbin/halt [-n] [-w] [-d] [-f] [-i] [-p] [-h]
/sbin/reboot [-n] [-w] [-d] [-f] [-i]
/sbin/poweroff [-n] [-w] [-d] [-f] [-i] [-h]
DESCRIPTION
Halt notes that the system is being brought down in the file /var/log/wtmp, and then either tells the kernel to halt, reboot or power-off
the system.
If halt or reboot is called when the system is not in runlevel 0 or 6, in other words when it's running normally, shutdown will be invoked
instead (with the -h or -r flag). For more info see the shutdown(8) manpage.
The rest of this manpage describes the behaviour in runlevels 0 and 6, that is when the systems shutdown scripts are being run.
OPTIONS -n Don't sync before reboot or halt. Note that the kernel and storage drivers may still sync.
-w Don't actually reboot or halt but only write the wtmp record (in the /var/log/wtmp file).
-d Don't write the wtmp record. The -n flag implies -d.
-f Force halt or reboot, don't call shutdown(8).
-i Shut down all network interfaces just before halt or reboot.
-h Put all hard drives on the system in stand-by mode just before halt or power-off.
-p When halting the system, switch off the power. This is the default when halt is called as poweroff.
DIAGNOSTICS
If you're not the superuser, you will get the message `must be superuser'.
NOTES
Under older sysvinit releases , reboot and halt should never be called directly. From release 2.74 on halt and reboot invoke shutdown(8) if
the system is not in runlevel 0 or 6. This means that if halt or reboot cannot find out the current runlevel (for example, when
/var/run/utmp hasn't been initialized correctly) shutdown will be called, which might not be what you want. Use the -f flag if you want to
do a hard halt or reboot.
The -h flag puts all hard disks in standby mode just before halt or power-off. Right now this is only implemented for IDE drives. A side
effect of putting the drive in stand-by mode is that the write cache on the disk is flushed. This is important for IDE drives, since the
kernel doesn't flush the write cache itself before power-off.
The halt program uses /proc/ide/hd* to find all IDE disk devices, which means that /proc needs to be mounted when halt or poweroff is
called or the -h switch will do nothing.
AUTHOR
Miquel van Smoorenburg, miquels@cistron.nl
SEE ALSO shutdown(8), init(8)
Nov 6, 2001 HALT(8)
07-11-2006
Installing RedHat 8.0 onto Dell PowerEdge SC1425 - hdc: status error: status = 0x58
