07-06-2006
They take the settings of the parent interface.
if looking at ce0:1 check the settings on ce0.
10 More Discussions You Might Find Interesting
1. Solaris
Hi ......
I'm trying to configure my Solaris servers with only one NIC card to have 2 IP addresses as well as 2 different default gateways.
( NOT to be confused with multi-pathing - with 2 physical IPs & 1 virtual ip)
Thanks,
Remi (1 Reply)
Discussion started by: Remi
1 Replies
2. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
3. Linux
Hi,
I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0
and my requirement is 100mbps full duplex.
Regards,
Manoj (3 Replies)
Discussion started by: manoj.solaris
3 Replies
4. Solaris
Hi everybody!
I'm facing a problem and I doubt about the solution (I'm not very familiar with old *NIXs).
An external network supplier (let's call them "telco") just installed new communication components that filters MAC addresses.
I have a Solaris 5 server, with 1 NIC (hte0) which is... (6 Replies)
Discussion started by: Isharfoxat
6 Replies
5. Linux
I have a linux box with 2 nic cards on it one for prod and one for backup.
My question is while the backup are happening how do I determine which nic is used for backups . I would like to run a command so that that I can see the usage in a dynamic fashion. (7 Replies)
Discussion started by: new2prog
7 Replies
6. Solaris
Hi All,
does any body know how to create Virtual NIC in Solaris 10
if any one have good article or reference
kindly provide me
i try to Google
but i didn't find good one (7 Replies)
Discussion started by: jamisux
7 Replies
7. UNIX for Advanced & Expert Users
Hi,
Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux.
I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Discussion started by: devtakh
3 Replies
8. Solaris
Hi All,
I am unable to detect NIC card in solaris 10 installed on X86 system after installation, every thing is installed properly, i have check bios settings in which it is detectable.
I suspect we have selected NETWORKED option as NO during installation.How to conform whether we have selected... (6 Replies)
Discussion started by: ravijanjanam12
6 Replies
9. Solaris
Hi,
I have few Solaris (9 and 10) servers, whose consoles are running on 10 MBPs. Now, Network team is changing their switch, which doesn't support 10 MBPs and we need to check if console all of those servers will support 100MBPs or more.
Is there any way to check supported (or maximum supported)... (7 Replies)
Discussion started by: solaris_1977
7 Replies
10. Red Hat
Hi,
I would like to know how to find out ACTUAL speed of NIC Card.
I have used the command ethtool eth0, it is showing supported modes,
but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
LEARN ABOUT CENTOS
ssl_clear
SSL_clear(3) OpenSSL SSL_clear(3)
NAME
SSL_clear - reset SSL object to allow another connection
SYNOPSIS
#include <openssl/ssl.h>
int SSL_clear(SSL *ssl);
DESCRIPTION
Reset ssl to allow another connection. All settings (method, ciphers, BIOs) are kept.
NOTES
SSL_clear is used to prepare an SSL object for a new connection. While all settings are kept, a side effect is the handling of the current
SSL session. If a session is still open, it is considered bad and will be removed from the session cache, as required by RFC2246. A
session is considered open, if SSL_shutdown(3) was not called for the connection or at least SSL_set_shutdown(3) was used to set the
SSL_SENT_SHUTDOWN state.
If a session was closed cleanly, the session object will be kept and all settings corresponding. This explicitly means, that e.g. the
special method used during the session will be kept for the next handshake. So if the session was a TLSv1 session, a SSL client object will
use a TLSv1 client method for the next handshake and a SSL server object will use a TLSv1 server method, even if SSLv23_*_methods were
chosen on startup. This will might lead to connection failures (see SSL_new(3)) for a description of the method's properties.
WARNINGS
SSL_clear() resets the SSL object to allow for another connection. The reset operation however keeps several settings of the last sessions
(some of these settings were made automatically during the last handshake). It only makes sense for a new connection with the exact same
peer that shares these settings, and may fail if that peer changes its settings between connections. Use the sequence SSL_get_session(3);
SSL_new(3); SSL_set_session(3); SSL_free(3) instead to avoid such failures (or simply SSL_free(3); SSL_new(3) if session reuse is not
desired).
RETURN VALUES
The following return values can occur:
0 The SSL_clear() operation could not be performed. Check the error stack to find out the reason.
1 The SSL_clear() operation was successful.
SSL_new(3), SSL_free(3), SSL_shutdown(3), SSL_set_shutdown(3), SSL_CTX_set_options(3), ssl(3), SSL_CTX_set_client_cert_cb(3)
1.0.1e 2014-06-17 SSL_clear(3)