07-06-2006
How to check Virtual NIC card speed on solaris
Hi,
We have a 4 port Sun gigaswift NIC card on our sun fire server.
If the card is a physical one I know how to check the settings/speed. But since this is a virtual card with 4 ports , I am not sure as how we can check the settings.
Details
-----------
root:/> ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
ce3: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet <IP ADD> netmask ffffff00 broadcast < ADD>
ether <ADD>
ce5: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 3
inet <ADD> netmask ffffff00 broadcast <ADD> ether <ADD>
|
|
so on
NOTE: I used ADD in the place of IP Add and mac address in the above output.
Thanks in advance.
10 More Discussions You Might Find Interesting
1. Solaris
Hi ......
I'm trying to configure my Solaris servers with only one NIC card to have 2 IP addresses as well as 2 different default gateways.
( NOT to be confused with multi-pathing - with 2 physical IPs & 1 virtual ip)
Thanks,
Remi (1 Reply)
Discussion started by: Remi
1 Replies
2. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
3. Linux
Hi,
I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0
and my requirement is 100mbps full duplex.
Regards,
Manoj (3 Replies)
Discussion started by: manoj.solaris
3 Replies
4. Solaris
Hi everybody!
I'm facing a problem and I doubt about the solution (I'm not very familiar with old *NIXs).
An external network supplier (let's call them "telco") just installed new communication components that filters MAC addresses.
I have a Solaris 5 server, with 1 NIC (hte0) which is... (6 Replies)
Discussion started by: Isharfoxat
6 Replies
5. Linux
I have a linux box with 2 nic cards on it one for prod and one for backup.
My question is while the backup are happening how do I determine which nic is used for backups . I would like to run a command so that that I can see the usage in a dynamic fashion. (7 Replies)
Discussion started by: new2prog
7 Replies
6. Solaris
Hi All,
does any body know how to create Virtual NIC in Solaris 10
if any one have good article or reference
kindly provide me
i try to Google
but i didn't find good one (7 Replies)
Discussion started by: jamisux
7 Replies
7. UNIX for Advanced & Expert Users
Hi,
Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux.
I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Discussion started by: devtakh
3 Replies
8. Solaris
Hi All,
I am unable to detect NIC card in solaris 10 installed on X86 system after installation, every thing is installed properly, i have check bios settings in which it is detectable.
I suspect we have selected NETWORKED option as NO during installation.How to conform whether we have selected... (6 Replies)
Discussion started by: ravijanjanam12
6 Replies
9. Solaris
Hi,
I have few Solaris (9 and 10) servers, whose consoles are running on 10 MBPs. Now, Network team is changing their switch, which doesn't support 10 MBPs and we need to check if console all of those servers will support 100MBPs or more.
Is there any way to check supported (or maximum supported)... (7 Replies)
Discussion started by: solaris_1977
7 Replies
10. Red Hat
Hi,
I would like to know how to find out ACTUAL speed of NIC Card.
I have used the command ethtool eth0, it is showing supported modes,
but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
LEARN ABOUT DEBIAN
vlan-interfaces
VLAN-INTERFACES(5) File formats VLAN-INTERFACES(5)
NAME
/etc/network/interfaces (vlan) - vlan extensions for the interfaces(5) file format
DESCRIPTION
/etc/network/interfaces contains network interface configuration information for the ifup(8) and ifdown(8) commands. This manpage
describes the vlan extensions to the standard interfaces(5) file format.
Primary extensions exist to make and destroy vlan interfaces, secondary extensions exist for ipv4 interface manipulation which are gener-
ally needed when using (a lot of) vlans.
VLAN CREATION
Vlan interface definitions exist of the vlan interface name, and an optional 'raw-device' parameter. Vlan interfaces are numbered 1 to
4095. You have the option to have interface names zero-padded to 4 numbers, or just the plain digits without leading zero. The following
example shows four ways to create a vlan with id 1 on interface eth0. They all result in different names.
iface eth0.1 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan1 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
iface eth0.0001 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan0001 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
# We don't have br support out of the box
iface br0.2 inet static
vlan-raw-device br0
address 192.168.1.1
netmask 255.255.255.0
# Aliases are ignored
iface br0.2:1 inet static
address 192.168.1.1
netmask 255.255.255.255
EXTRA IFACE OPTIONS
Usually someone who uses vlans also wants to do some other manipulations with the ip stack or interface.
vlan-raw-device devicename
Indicates the device to create the vlan on. This is ignored when the devicename is part of the vlan interface name.
ip-proxy-arp 0|1
Turn proxy-arp off or on for this specific interface. This also works on plain ethernet like devices.
ip-rp-filter 0|1|2
Set the return path filter for this specific interface. This also works on plain ethernet like devices.
hw-mac-address mac-address
This sets the mac address of the interface before bringing it up. This works on any device that allows setting the hardware address
with the ip command.
AUTHOR
This manpage was adapted from interfaces(5) by Ard van Breemen <ard@kwaak.net>
SEE ALSO
vconfig(8) interfaces(5)
vlan September 30 2007 VLAN-INTERFACES(5)