Although, question isn't clear, but I assume you have 2 subnets, connecting thru VPN, subnet1 UNIX machines are able to ping locally within subnet1 and same is the case with subnet2. But subnet1 machines aren't able to ping subnet2 machines thru the VPN, right?
At all UNIX machines at both subnets, add your default gateway:
Code:
route add default 192.168.0.100
Where 192.168.0.100 is the private IP address of your VPN device local to that particular subnet, also make sure that your VPN device allows packets from your local machines to pass thru. Sometimes it happens that every thing is configured properly but UNIX machine doesn't have access to internet or foreign IP address, check that also.
If it doesn't help, pls provide some more details.
We have an older model DG Aviion Unix system and we're trying to switch to VPN but we can't talk to the Unix box... can't ping or telnet to it, but we can talk to all our other systems (PC/NT servers).
Is there a network/tcpip setting we're missing? Something we have to change/set, either on... (0 Replies)
Hi,
My setup is as follows:
1) HeadOffice----->Private subnet: 192.168.0.0
2) Branch1-------->Private subnet: 192.168.200.0
I'm connecting from branch1 to headoffice thru VPN and I'm able to access all PC's except SCO UNIXWARE 7.1.1 box.
I have made a search before posting this... (7 Replies)
Hi,
I want to work on a remote unix server, then on a windows XP station I have a Forticlient that makes a VPN to the network on which the server is situated. But then I do not know how to work with. In DOS box (cmd BOX) I issue:
telnet myserver
but It does not know IT.
Any idea ?
Many thanks. (2 Replies)
Trying to connect to my companies VPN with vpnc but I keep getting an error that the target failed to respond. I run wireshark and see that my host sends out a few ISAKMP packets but gets no response and gives up.
Any ideas what can cause this to happen? Is there someway that UDP traffic could... (0 Replies)
I am looking for a solution to add a web banner in all web page sessions when user is connected through pptp vpn connection.
any solution? may be using squid or pptp servers? (1 Reply)
Hi,
I have been using using internet explorer on windows for connecting with production server using vpn connection.
i want to use same vpn to connect from solaris system to the production server.it is not connecting
is there solution (0 Replies)
Hello Gurus :
I had a question about VPN connection . Say for instance i have to connect from my point A to point B (Is the place where i initiate the VPN connection ) . From there i connect to point C (i.e Bank) .
My question is this a secure connection . (from point A to C)
Thanks... (3 Replies)
Hi.
Yesterday I installed Solaris 11.3 and I tried to setup a VPN but I didn't find how to make it.
I saw the "network manager" where I found the ethernet connection but I didn't find where to add a VPN connection.
When I used Debian Linux there was NetworkManagerVPN that with a GUI I... (0 Replies)
Discussion started by: Jena
0 Replies
LEARN ABOUT MOJAVE
racoonctl
RACOONCTL(8) BSD System Manager's Manual RACOONCTL(8)NAME
racoonctl -- racoon administrative control tool
SYNOPSIS
racoonctl [opts] reload-config
racoonctl [opts] show-schedule
racoonctl [opts] show-sa [isakmp|esp|ah|ipsec]
racoonctl [opts] get-sa-cert [inet|inet6] src dst
racoonctl [opts] flush-sa [isakmp|esp|ah|ipsec]
racoonctl [opts] delete-sa saopts
racoonctl [opts] establish-sa [-w] [-n remoteconf] [-u identity] saopts
racoonctl [opts] vpn-connect [-u identity] vpn_gateway
racoonctl [opts] vpn-disconnect vpn_gateway
racoonctl [opts] show-event
racoonctl [opts] logout-user login
DESCRIPTION
racoonctl is used to control racoon(8) operation, if ipsec-tools was configured with adminport support. Communication between racoonctl and
racoon(8) is done through a UNIX socket. By changing the default mode and ownership of the socket, you can allow non-root users to alter
racoon(8) behavior, so do that with caution.
The following general options are available:
-d Debug mode. Hexdump sent admin port commands.
-l Increase verbosity. Mainly for show-sa command.
-s socket
Specify unix socket name used to connecting racoon.
The following commands are available:
reload-config
This should cause racoon(8) to reload its configuration file.
show-schedule
Unknown command.
show-sa [isakmp|esp|ah|ipsec]
Dump the SA: All the SAs if no SA class is provided, or either ISAKMP SAs, IPsec ESP SAs, IPsec AH SAs, or all IPsec SAs. Use -l to
increase verbosity.
get-sa-cert [inet|inet6] src dst
Output the raw certificate that was used to authenticate the phase 1 matching src and dst.
flush-sa [isakmp|esp|ah|ipsec]
is used to flush all SAs if no SA class is provided, or a class of SAs, either ISAKMP SAs, IPsec ESP SAs, IPsec AH SAs, or all IPsec
SAs.
establish-sa [-w] [-n remoteconf] [-u username] saopts
Establish an SA, either an ISAKMP SA, IPsec ESP SA, or IPsec AH SA. The optional -u username can be used when establishing an ISAKMP
SA while hybrid auth is in use. The exact remote block to use can be specified with -n remoteconf. racoonctl will prompt you for
the password associated with username and these credentials will be used in the Xauth exchange.
Specifying -w will make racoonctl wait until the SA is actually established or an error occurs.
saopts has the following format:
isakmp {inet|inet6} src dst
{esp|ah} {inet|inet6} src/prefixlen/port dst/prefixlen/port
{icmp|tcp|udp|gre|any}
vpn-connect [-u username] vpn_gateway
This is a particular case of the previous command. It will establish an ISAKMP SA with vpn_gateway.
delete-sa saopts
Delete an SA, either an ISAKMP SA, IPsec ESP SA, or IPsec AH SA.
vpn-disconnect vpn_gateway
This is a particular case of the previous command. It will kill all SAs associated with vpn_gateway.
show-event
Listen for all events reported by racoon(8).
logout-user login
Delete all SA established on behalf of the Xauth user login.
Command shortcuts are available:
rc reload-config
ss show-sa
sc show-schedule
fs flush-sa
ds delete-sa
es establish-sa
vc vpn-connect
vd vpn-disconnect
se show-event
lu logout-user
RETURN VALUES
The command should exit with 0 on success, and non-zero on errors.
FILES
/var/racoon/racoon.sock or
/var/run/racoon.sock racoon(8) control socket.
SEE ALSO ipsec(4), racoon(8)HISTORY
Once was kmpstat in the KAME project. It turned into racoonctl but remained undocumented for a while. Emmanuel Dreyfus <manu@NetBSD.org>
wrote this man page.
BSD March 12, 2009 BSD