05-01-2006
8 More Discussions You Might Find Interesting
1. Solaris
Hi,
Can anyone suggest me any USB Hard Disk Drive which I can connect to Sun Fire V890 and take backup at a quick speed. A test with SolidState USB Hard Drive for backup work was taking writing at 2GB per hour for a 75GB backup.
Regards,
Tushar Kathe (1 Reply)
Discussion started by: tushar_kathe
1 Replies
2. Solaris
Hello,
Wondering if anyone can help me with mounting a file share from my Sun T2000 server running Solaris 10 to my connected 2530 disk array?
I believe I've connected the disk array correctly and I have created a volume on the array using the filesystem (Sun_SAM-FS, RAID-5).
The T2000... (15 Replies)
Discussion started by: DundeeDancer
15 Replies
3. Solaris
Hi all.
I am seeing in one of our less-used servers that it crashed and now won't restart. I get the message 'continue with normal startup or boot into maintenance mode'.
I go into maintenance and run fsck on /usr0 (mentioned in error at restart) it then reboots but goes right back to... (3 Replies)
Discussion started by: jamie_collins
3 Replies
4. Red Hat
in red hat 4, 5 any one know any commands or any scritps to monitor HP DL 380 G5/6 server and trigger alarm when hard disk failed.
thanks for all support
---------- Post updated at 02:45 PM ---------- Previous update was at 12:00 PM ----------
does HP ProLiant Support Pack support is... (4 Replies)
Discussion started by: maxlee24
4 Replies
5. Linux
Hi all,
I'm kind of new to programming in Linux & c/c++. I'm currently writing a FileManager using Ubuntu Linux(10.10) for Learning Purposes. I've got started on this project by creating a loopback device to be used as my virtual hard disk. After creating the loop back hard disk and mounting it... (23 Replies)
Discussion started by: shen747
23 Replies
6. Solaris
I need to add two new hard drives of 300 GB capacity to a SunSPARC T5440 server. The server currently has two hard drives of 146 GB each.
How do I add the new drives to the existing UFS?
What are the procedures involved in setting this server with the new hard drives? I am very new to Solaris... (6 Replies)
Discussion started by: ramatnmcc
6 Replies
7. Hardware
does anyone know where to look for that piece of metal attached to hard drive that inserts it into server (fire v125)? I've tried ebay, with no luck. (seller requires verified paypal address which is unpossible here) (0 Replies)
Discussion started by: orange47
0 Replies
8. Solaris
Hi,
I have a Sun Fire V440 server that fails to boot up correctly. A lot of services are not started and the sytems acts really slow to commands. During boot I can see the following Error:
WARNING: /pci@1f,700000/scsi@2/sd@0,0 (sd1):
SCSI transport failed: reason 'reset': retrying... (15 Replies)
Discussion started by: oliwei
15 Replies
hdio(7I) Ioctl Requests hdio(7I)
NAME
hdio - SMD and IPI disk control operations
SYNOPSIS
#include <sys/hdio.h>
DESCRIPTION
Note - The SMC and IPI drivers have been discontinued. dkio(7I) is now the preferred method for retrieving disk information.
The SMD and IPI disk drivers supplied with this release support a set of ioctl(2) requests for diagnostics and bad sector information.
Basic to these ioctl() requests are the definitions in <sys/hdio.h>.
IOCTLS
HDKIOCGTYPE The argument is a pointer to a hdk_type structure (described below). This ioctl() gets specific information from the hard
disk.
HDKIOCSTYPE The argument is a pointer to a hdk_type structure (described below). This ioctl() sets specific information about the hard
disk.
/*
* Used for drive info
*/
struct hdk_type {
ushort_t hdkt_hsect; /* hard sector count (read only) */
ushort_t hdkt_promrev; /* prom revision (read only) */
uchar_t hdkt_drtype; /* drive type (ctlr specific) */
uchar_t hdkt_drstat; /* drive status (ctlr specific, ro) */
};
HDKIOCGBAD The argument is a pointer to a hdk_badmap structure (described below). This ioctl() is used to get the bad sector map from
the disk.
HDKIOCSBAD The argument is a pointer to a hdk_badmap structure (described below). This ioctl() is used to set the bad sector map on
the disk.
/*
* Used for bad sector map
*/
struct hdk_badmap {
caddr_t hdkb_bufaddr; /* address of user's map buffer */
};
HDKIOCGDIAG The argument is a pointer to a hdk_diag structure (described below). This ioctl() gets the most recent command that failed
along with the sector and error number from the hard disk.
/*
* Used for disk diagnostics
*/
struct hdk_diag {
ushort_t hdkd_errcmd; /* most recent command in error */
daddr_t hdkd_errsect; /* most recent sector in error */
uchar_t hdkd_errno; /* most recent error number */
uchar_t hdkd_severe; /* severity of most recent error */
};
SEE ALSO
ioctl(2), dkio(7I)
SunOS 5.10 13 Aug 2002 hdio(7I)