04-28-2006
As the mounting fails
it could be that your fstab is broken.
Btw. afaik there is no mountall command or alias on HP-UX.
Issue mount -a instead.
Also issue /sbin/cat /etc/fstab
and look if all the entries are valid.
Maybe a volume couldn't be activated?
Do you have an LVM layout?
Do you have your root disks mirrored?
Maybe a mirror disk is broken and the quorum for vg00 couldn't be fullfilled on activation?
You then could try to activate it by
/sbin/vgchange -q n -a y vg00
Maybe a filesystem didn't pass the fsck?
There can be all sorts of reasons,
and it's difficult to tell without further information.
You should check /etc/rc.log and /var/adm/syslog/syslog.log and dmesg
for any hints what caused init to hang.
Of course that would require to get /var mounted first.
Also note that syslog.log gets moved to OLDsyslog on every reboot.
So you might wish to save the syslog.log
Last edited by RTM; 05-06-2006 at 09:30 AM..
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
i am currently am planning to start a webserver to host a community of webpages, but i need help getting started? anyone have any sites or advice for me? thanks! (1 Reply)
Discussion started by: bowlofrice
1 Replies
2. IP Networking
Solaris v5.6
how do you stop and start the network services? (4 Replies)
Discussion started by: Westy564
4 Replies
3. Solaris
i have installed solaris 10 on PIII i Ghz cpu,
whole installation carried out in GUI mode but after installation it is unable to start GUI mode.
Error is : "X server can not be started on display 0"
screed flickers twice and the CLI login prompt appears (1 Reply)
Discussion started by: ajays
1 Replies
4. UNIX for Dummies Questions & Answers
Hi There
Kindly inform me on how to start and stop the print services in Unix from the command line. (2 Replies)
Discussion started by: esh
2 Replies
5. Solaris
Hi Gurus
Sorry to ask this question again but left with no option
I have entry in /etc/dfs/dfstab for resources which i am welling to shaer over the netwrok. Idelay once i execute shaerall it should enabel the nfs/server servcie in Solaris 10, however it was not stared and later i tried... (2 Replies)
Discussion started by: kumarmani
2 Replies
6. UNIX for Advanced & Expert Users
Sir,
I have installed an Apache server in Fedora 9 (packages)
and when i go to etc folder and try the command
httpd -k start
it says command not found....can any one help me out!!!
---------- Post updated at 12:02 PM ---------- Previous update was at 11:46 AM ----------
When i... (4 Replies)
Discussion started by: bssandeshbs
4 Replies
7. Solaris
Hi,
I do not get nfs/server started.
bash-3.00# svcadm enable nfs/server
bash-3.00# svcs -a |grep nfs
disabled 21:44:36 svc:/network/nfs/cbd:default
disabled 21:44:36 svc:/network/nfs/client:default
disabled 21:44:51 svc:/network/nfs/rquota:default
disabled ... (4 Replies)
Discussion started by: jld
4 Replies
8. Solaris
hi guys
i try to start my web server on solaris 10 with T2000 server, i have been already start but the status always maintenace. when i check logfile i have this messages
when i exceute " svcs -l http" i have this output
fmri svc:/network/http:apache2
name ... (10 Replies)
Discussion started by: audi_99
10 Replies
9. SCO
Hi all,
I have a customer whose sco unix server wasnt power off correctly and when booting it up I noticed that the boot up takes a while to finish the " Starting TCP services: snmpd routed lpd". after that the server is ready for login, but you cannot ping anything from the server (apart from... (2 Replies)
Discussion started by: CharlL
2 Replies
10. Linux
Hi All,
My application uses three different sub-services to make complete application up and running to normal.
The entry of all the three services are present in /etc/init.d directory with proper softlink created to application home path where it actually exists.
In one rare case one of the... (3 Replies)
Discussion started by: hk_kamozalwar
3 Replies
LEARN ABOUT HPUX
show_cached_server
show cached server(1m) show cached server(1m)
NAME
show cached server - Displays address information of a server in the local clerk's cache
SYNOPSIS
show cached server name
ARGUMENTS
A simple name for the cached server. The name can contain wildcard characters.
DESCRIPTION
The show cached server command displays address information of a server in the local clerk's cache. The following list describes the valid
attributes: The directory cell name The protocol sequence and network address of the server node
Privilege Required
You must have read permission to the clerk.
NOTE
This command is replaced at Revision 1.1 by the dcecp command and may not be provided in future releases of DCE.
EXAMPLES
The following command displays all attributes of the cached server emv. cdscp> show cached server emv*
SHOW
CACHED NAMESERVER emv_udp
AT 1991-10-15-15:56:56
Name = /.../emv.abc.com
Tower = ncadg_ip_udp:14.20.14.32
Tower = ncacn_ip_tcp:14.20.14.32
SHOW
CACHED NAMESERVER emv_tcp
AT 1991-10-15-15:56:57
Name = /.../emv.abc.com
Tower = ncadg_ip_udp:14.20.14.32
Tower = ncacn_ip_tcp:14.20.14.32
RELATED INFORMATION
Commands: clear cached server(1m), define cached server(1m)
show cached server(1m)