04-26-2006
The server is not starting all services
Hi everybody
When I Boot/restart my HP-UX server when it reaches the step described below doesn't go through. When I kick a key in the console it show me the login prompt and a can log on but I cannot access the server from the network, I can only do it via LAN console.
Please, can you help me to solve this problem?
Regards,
Gege
HP-UX Start-up in progresstware clause in DFARS 252.227-7013.
__________________________
Configure system crash dumps .......................................OK
Mount file systems .....................................................
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
i am currently am planning to start a webserver to host a community of webpages, but i need help getting started? anyone have any sites or advice for me? thanks! (1 Reply)
Discussion started by: bowlofrice
1 Replies
2. IP Networking
Solaris v5.6
how do you stop and start the network services? (4 Replies)
Discussion started by: Westy564
4 Replies
3. Solaris
i have installed solaris 10 on PIII i Ghz cpu,
whole installation carried out in GUI mode but after installation it is unable to start GUI mode.
Error is : "X server can not be started on display 0"
screed flickers twice and the CLI login prompt appears (1 Reply)
Discussion started by: ajays
1 Replies
4. UNIX for Dummies Questions & Answers
Hi There
Kindly inform me on how to start and stop the print services in Unix from the command line. (2 Replies)
Discussion started by: esh
2 Replies
5. Solaris
Hi Gurus
Sorry to ask this question again but left with no option
I have entry in /etc/dfs/dfstab for resources which i am welling to shaer over the netwrok. Idelay once i execute shaerall it should enabel the nfs/server servcie in Solaris 10, however it was not stared and later i tried... (2 Replies)
Discussion started by: kumarmani
2 Replies
6. UNIX for Advanced & Expert Users
Sir,
I have installed an Apache server in Fedora 9 (packages)
and when i go to etc folder and try the command
httpd -k start
it says command not found....can any one help me out!!!
---------- Post updated at 12:02 PM ---------- Previous update was at 11:46 AM ----------
When i... (4 Replies)
Discussion started by: bssandeshbs
4 Replies
7. Solaris
Hi,
I do not get nfs/server started.
bash-3.00# svcadm enable nfs/server
bash-3.00# svcs -a |grep nfs
disabled 21:44:36 svc:/network/nfs/cbd:default
disabled 21:44:36 svc:/network/nfs/client:default
disabled 21:44:51 svc:/network/nfs/rquota:default
disabled ... (4 Replies)
Discussion started by: jld
4 Replies
8. Solaris
hi guys
i try to start my web server on solaris 10 with T2000 server, i have been already start but the status always maintenace. when i check logfile i have this messages
when i exceute " svcs -l http" i have this output
fmri svc:/network/http:apache2
name ... (10 Replies)
Discussion started by: audi_99
10 Replies
9. SCO
Hi all,
I have a customer whose sco unix server wasnt power off correctly and when booting it up I noticed that the boot up takes a while to finish the " Starting TCP services: snmpd routed lpd". after that the server is ready for login, but you cannot ping anything from the server (apart from... (2 Replies)
Discussion started by: CharlL
2 Replies
10. Linux
Hi All,
My application uses three different sub-services to make complete application up and running to normal.
The entry of all the three services are present in /etc/init.d directory with proper softlink created to application home path where it actually exists.
In one rare case one of the... (3 Replies)
Discussion started by: hk_kamozalwar
3 Replies
cdsd(1m) cdsd(1m)
NAME
cdsd - Starts the CDS server
SYNOPSIS
cdsd [-a] [-D] [-l principal] [-w route]
ARGUMENTS
Creates a new namespace if there is not an existing namespace. This flag is meaningful only when the cell is first configured (that is, the
initial creation of the namespace). For debugging use only. Causes the cdsd process not to fork. Locksmith mode. Allows the principal
specified to have full access to all information stored with this server. Routes serviceability messages.
DESCRIPTION
The cdsd command starts the CDS server.
Privilege Required
You must log in as superuser (root).
NOTES
This command is ordinarily executed by a DCE configuration or startup script. You should use this command interactively only when a cdsd
fails to start automatically after a reboot, or if you want to restart a cdsd after disabling it to perform a backup or to do diagnostic
work on the host system.
EXAMPLE
To restart a cdsd server, follow these steps: Log in to the server system as superuser (root). Verify that the dced and cdsadv processes
are running. Enter the following command to restart the CDS server: # cdsd
When the server process starts, it starts all clearinghouses on the system.
RELATED INFORMATION
Books: OSF DCE Administration Guide
cdsd(1m)