Sponsored Content
Full Discussion: Switching SAN storage
Special Forums Hardware Filesystems, Disks and Memory Switching SAN storage Post 302071625 by frustrated1 on Saturday 22nd of April 2006 09:03:06 PM
Old 04-22-2006
Well - all depends.. you may have gotten lucky and the previous admin may have installed all software on the san storage - with no device files etc on local disk...

But... Chances are... not everything is on the san and 50% are on the local disk..
If you are still connected to the old server.. you are best to remove those packages and then re-install when on new server.. Thats my thought anyway unless anyone has any better idea's
 

9 More Discussions You Might Find Interesting

1. Solaris

Using San storage - advice needed

Thinking of using our San for network backups.. Have a Netra 240 being installed and planning to get some space on our San. Do you know what software is used to access the San from my server or what I would need to do? I know how to connect to local storage, disk arrays etc but not sure what... (1 Reply)
Discussion started by: frustrated1
1 Replies

2. AIX

SAN storage and speed

I have 3 SAN disks of 1 TB each. Is it more efficient to make 1 large Volume group with multiple LV's or 3 Volume Groups with 1 LV each. The SAN disk is where all my backups will be dumped.:confused: (1 Reply)
Discussion started by: daveisme
1 Replies

3. Solaris

SAN Storage to solaris 10 server

Hi, I have configured our SAN Storage to be connected to our new SUN T5220. On the SAn it looks all fine on the server I do not see any connection: cfgadm -al Ap_Id Type Receptacle Occupant Condition c1 scsi-bus connected ... (4 Replies)
Discussion started by: manni2
4 Replies

4. Red Hat

how do we check SAN storage?

Hello, I am using LINUX OS. I want to check what is the SAN storage size. How do i check this in server? Any help is really appreciated.. (3 Replies)
Discussion started by: govindts
3 Replies

5. Solaris

Cannot see the IBM SAN storage

HI all, I had recently change the Server storage from EMC to the IBM SAN. but after the configuration, the IBM success to see the server HBA port and successfully assign a LUN for the server. When i go to the server, and restarted it. i use the "format" command to check, but din see any... (1 Reply)
Discussion started by: SmartAntz
1 Replies

6. UNIX for Dummies Questions & Answers

Storage from SAN

hi guys I installed Centos 5.5 (local disk). I am using 2 HBAs Now I mapped 5 LUNs from a Storage. I will be using LVM just to test I assigned a LUN I've read I have to use multipath to avoid my Centos see the LUN twice I enabled mdmpd and multipathd... something else I should do? ... (8 Replies)
Discussion started by: kopper
8 Replies

7. Solaris

SAN Storage for ASM

Hi, We are planning to setup a 10gR2 RAC and storage on ASM. We use Sun StorEdge SAN. The installation and configuration manual says to configure ASM diskgroups with raw devices (preferably raw disk not volumes). I dont really know if its possible to present raw disks to the Solaris... (4 Replies)
Discussion started by: esmgr
4 Replies

8. AIX

New to San Storage

Can anyone recommend a good book on san storage basics and how it communicates with an AIX server? (1 Reply)
Discussion started by: NycUnxer
1 Replies

9. Linux

RH Switching rootvg/sanvg to New SAN

Hi, what's the safest procedure to reconfigure RH BFS to a new SAN? Current setup boots rootvg and sanvg from a SAN. Now a new SAN LUN is presented to the Linux Server. The first and second SAN are srdf'd - so they are always in sync. Can I re-use the existing LVM structure and somehow... (3 Replies)
Discussion started by: rfransix
3 Replies
installboot(1M) 														   installboot(1M)

NAME
installboot - install bootblocks in a disk partition SYNOPSIS
installboot bootblk raw-disk-device The boot(1M) program, ufsboot, is loaded from disk by the bootblock program which resides in the boot area of a disk partition. The ufs boot objects are platform-dependent, and reside in the /usr/platform/platform-name/lib/fs/ufs directory. The platform name can be found using the -i option of uname(1). The installboot utility is a SPARC only program. It is not supported on the architecture. users should use installgrub(1M) instead. bootblk The name of the bootblock code. raw-disk-device The name of the disk device onto which the bootblock code is to be installed; it must be a character device which is read- able and writable. Naming conventions for a SCSI or IPI drive are c?t?d?s? and c?d?s? for an IDE drive. Example 1: Installing UFS Boot Block To install a ufs boot block on slice 0 of target 0 on controller 1 of the platform where the command is being run, use: example# installboot /usr/platform/`uname -i`/lib/fs/ufs/bootblk /dev/rdsk/c1t0d0s0 /usr/platform/platform-name/lib/fs/ufs directory where ufs boot objects reside. /platform/platform-name/ufsboot second level program to boot from a disk or CD See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcsu | +-----------------------------+-----------------------------+ od(1), uname(1), boot(1M), init(1M), kadb(1M), kernel(1M), monitor(1M), reboot(1M), rpc.bootparamd(1M), init.d(4), attributes(5) WARNINGS
The installboot utility fails if the bootblk or openfirmware files do not exist or if the raw disk device is not a character device. 11 Apr 2005 installboot(1M)
All times are GMT -4. The time now is 08:39 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy