04-12-2006
probe-scsi-all hangs probing D1000
Hi folks,
I´m having a problem with a Ultra60 box with diff scsi pci card
conected to one D1000. The conection are correct because a checked the
D1000 guide. When a do probe-scsi-all in the OBP, the D1000 blink all
disks one time then the led of one of the disks powers off and then
nothing else appens. The OBP frezes, serching for something on that
controller forever. Can anyone give me a hand.
Thanks in advance.
Best regards.
8 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hello,
I'm running Red Hat Linux on a Dell Poweredge 2650 Rack Server and wondered if anyone knew of a tool or command I could use to probe the memory slots on the motherboard.
I know the machine has six memory slots and currently contains 1GB RAM, what I don't know however, is if it contains... (3 Replies)
Discussion started by: cw1972
3 Replies
2. Solaris
I am setting up a Storedge Multipack and upon booting(stop + a) I did a probe-scsi all.
Is there any way of viewing this output one page at a time?....it scrolls by too fast and I cannot get all the info.
Also it lists the drives here, but after logging in format does not show them.
How... (7 Replies)
Discussion started by: finster
7 Replies
3. Solaris
I have run init 0 to bring it to OK prompt.
I know that probe-scsi-all can hang the system.
I want to know what is the difference between probe-scsi-all and probe-scsi.
I was told that probe-scsi-all external and internal devices and probe-scsi shows only internal devices. what dose this ... (3 Replies)
Discussion started by: nitinkgoud
3 Replies
4. UNIX for Advanced & Expert Users
Hi All,
Is there anyway two nodes can share D1000 or minipack with 6 disk slots.
Right now I have minipacks and I am connecting to Sunblade 100 and Sunbladew 150 separately. I would like to connect two systems to one minipack and able see the all the disks on both systems.
I do have D1000... (0 Replies)
Discussion started by: sriny
0 Replies
5. Solaris
Hi,
Recently i was trying to connect Sun Storedge D1000 Array to E420 R (Practice servers). I connected the SCSI cable between array and server. I tried the following :
#devfsadm (nothing showed up)
#format (no new disk is shown here)
i tried this process again after putting ON the... (2 Replies)
Discussion started by: bluegold86
2 Replies
6. Solaris
i have a new netra 240 server when i make probe-scsi in obp i have this output :
ERROR: /pci@1c,600000: Last Trap: Fast Data Access MMU Miss
am upgarading obp firmware but the problem is always here
the os solaris 10) is installed correctely and i can use it , when i type #format i can see... (2 Replies)
Discussion started by: lid-j-one
2 Replies
7. Solaris
HI
I have a V240 server and the probe-scsi-all on the Ok prompt is taking forever.
I have tried powercycling the server multiple times.
also tried set-defaults and reset-all..
COuld anyone tell the solution to this.. I have run out of options now.
Following is the only thing... (8 Replies)
Discussion started by: ningy
8 Replies
8. Solaris
Can anyone explain the output of probe-scsi command below?
ok probe-scsi
Target 0
Unit 0 Disk SEAGATE ST373207LSUN72G 045A
Target 1
Unit 0 Disk SEAGATE ST373207LSUN72G 045A
I have no idea what it means. I tried to read online but I still did not understand. I appreciate... (6 Replies)
Discussion started by: cjashu
6 Replies