Sponsored Content
Full Discussion: routing problem in solaris
Special Forums IP Networking routing problem in solaris Post 302070877 by stdout on Sunday 9th of April 2006 02:44:44 PM
Old 04-09-2006
hello,

if your 10.100.a.b behind somekind of NAT - you need to pass the traffic through a static port translation so your server can reach the other end.
a static route maybe wont do the trick.

cheers.

Last edited by stdout; 04-09-2006 at 03:55 PM..
 

10 More Discussions You Might Find Interesting

1. IP Networking

Routing problem

Hi I know this problem is more likely some windows problem but it has also something to do with unix. We have a windows nt environment wich uses AIX (unix) machines as file servers (samba). In our windows network environment we nicely see al the unix file servers via the 10 MB network. Last... (2 Replies)
Discussion started by: Mark Detrez
2 Replies

2. IP Networking

routing problem

following Problem. I configured my SuSE Linux 8.0 as a router. I4l, named, ip_forward, iptables (NAT/MASQUERADING) are running or are aktivatet. I just can get a internet connection about the proxy server squid, but if i want to use other protocols i need functional routing. (I had this... (1 Reply)
Discussion started by: razor
1 Replies

3. IP Networking

Routing Problem

I have a question concerning networking. Could any forum members explain to me why I might be getting "no route to host" messages when I try to connect through ftp and http protocols? I have went to my etc/hosts file and everything seems to be configured properly. I can connect within my... (1 Reply)
Discussion started by: cstovall
1 Replies

4. IP Networking

solaris 8 networking routing

hi all, how do i make sure that the new routing should take effect on the os memory right away? what should i run after i add all the new "route add ....". I have an example below: bash-2.03# netstat -rn Routing Table: IPv4 Destination Gateway Flags Ref Use Interface... (1 Reply)
Discussion started by: itik
1 Replies

5. Solaris

Routing problem of Solaris

Hi, I got problem of Sun Solaris 8 routing. IP of SunA is 10.16.64.164, and have routing table: 10.16.64.0 10.16.64.164 U 1 19236 bge1 10.6.0.0 10.6.0.3 U 1 16534 bge0 224.0.0.0 10.6.0.3 U 1 ... (4 Replies)
Discussion started by: milo
4 Replies

6. Solaris

ip routing in solaris

I have a SUN ultra 5 machine running Solaris 6. it has two ethernet interfaces qe0 192.168.0.111 and qe1 192.168.1.111 the two subnets are 192.168.0.111 255.255.255.0 192.168.1.111 255.255.255.0 the specified routes are add route -net 192.168.0.0 255.255.255.0 192.168.0.111 add route... (3 Replies)
Discussion started by: adol65
3 Replies

7. IP Networking

solaris routing between two networks

ce0: flags=1100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4> mtu 1500 index 2 inet 10.162.212.132 netmask ffffff00 broadcast 10.162.212.255 ether 0:14:4f:55:82:9 ce1: flags=1100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4> mtu 1500 index 3 inet 10.231.11.232 netmask... (1 Reply)
Discussion started by: busyboy
1 Replies

8. Solaris

solaris routing between two networks

ce0: flags=1100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4> mtu 1500 index 2 inet 10.162.212.132 netmask ffffff00 broadcast 10.162.212.255 ether 0:14:4f:55:82:9 ce1: flags=1100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4> mtu 1500 index 3 inet 10.231.11.232 netmask... (3 Replies)
Discussion started by: busyboy
3 Replies

9. Solaris

Routing problem

Hi, I have two physical interfaces on a servers. We have connected them to differerent subnets. 1) First interface: 10.158.49.87 to newtwork 10.158.49.0, its gateway is 10.158.49.1 (It is added as default gateway) It is existing set up. It works well 2) Second interface: ... (1 Reply)
Discussion started by: sri243
1 Replies

10. Solaris

Solaris Routing

Hello All, Problem is that redundancy doesn't work, probably a routing issue I need to get sorted out When 172.29.11.x net is down, neither node3 nor node4 is trying 172.29.12.x network,The problem lies in network 172.29.13.x if 172.29.11.x network is down, node3/node4 should route to... (6 Replies)
Discussion started by: nadeemahmed
6 Replies
DUMP_SOCKDFR(8) 					      System Manager's Manual						   DUMP_SOCKDFR(8)

NAME
dump_sockdfr - Display contents of frozen route file for SOCKS server SYNOPSIS
dump_sockdfr [infile] DESCRIPTION
dump_sockdfr reads in a frozen route file for the SOCKS server and produces a listing of its contents on the standard output. The argument is optional; if omitted, /etc/sockd.fr is assumed. The frozen route file is produced by make_sockdfr and is essentially the memory image of the parsed route file. Using the frozen route file can reduce the start-up delay of the SOCKS server program since it no longer has to parse the file contents. When the SOCKS server starts, it always looks for the frozen route file /etc/sockd.fr first. If that file is not found, it then tries to use the plain-text route file /etc/sockd.route. If you use frozen route file, you must remember to run make_sockdfr every time after you modify the plain-text file or the SOCKS server will continue to use the frozen version of a previous route file. FILES
/etc/sockd.fr, /etc/sockd.route SEE ALSO
make_sockdfr(8), sockd.fr(5), sockd.route(5) AUTHOR
Ying-Da Lee, yingda@esd.sgi.com or yingda@best.com May 6, 1996 DUMP_SOCKDFR(8)
All times are GMT -4. The time now is 09:57 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy