04-08-2006
It's been discussed ....
The administration team is aware of sproadic post count problems, and we have discussed it briefly sometimes in the past. It seems to occur randomly every now and then for some short period of time. There is nothing we can do at the moment to rectify the problem permanently.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi ,
I am using SUN OS Version 5.6.
I have a file that contains records of length 270. when I do 'set nu' in vi editor, I get the count as 86. whereas when I do "wc -l" on the command prompt, it shows the count as only 85. this is very strange. why would the 'wc' show 1 record less. The job... (3 Replies)
Discussion started by: tselvanin
3 Replies
2. Filesystems, Disks and Memory
I had a power outage a day ago and when the power came back on my FreeBSD 4.6 webserver had problems. It said it was unable to mount /var and made me start in single user mode and said to run fsck MANUALY. So i did and this is now what i get.
www# fsck /dev/ad0s1e
** /dev/ad0s1e
BAD SUPER... (4 Replies)
Discussion started by: matthewbane
4 Replies
3. Solaris
/pci@if,0/pci@1,1/ide@3/dad@0,0 corrupt label wrong magic number
can u plz suggustion me (6 Replies)
Discussion started by: tirupathi
6 Replies
4. Filesystems, Disks and Memory
Whenever i run,
# fsck -F ufs /dev/dsk/c0t0d0s7
The following error prompt out:-
** /dev/dsk/c0t0d0s7
BAD SUPER BLOCK: MAGIC NUMBER WRONG
USE AN ALTERNATE SUPER-BLOCK TO SUPPLY NEEDED INFORMATION;
eg. fsck -o b=#
where # is the alternate super block. SEE fsck_ufs(1M).
... (3 Replies)
Discussion started by: beginningDBA
3 Replies
5. Solaris
I have created 1 LUN.
1)LUN 00BB 200GB /dev/rdsk/c1t3d44
/dev/rdsk/c2t28d44
/dev/rdsk/c3t19d44
/dev/rdsk/c4t12d44
2) Already added the new entry into sd.conf and rebooted.
3) Already done these:
powercf –q
power config
4) power display dev=all
I can see the new Symmetrix device.... (1 Reply)
Discussion started by: sirius20d
1 Replies
6. Solaris
Is there a way to recover label?
I could install (sparc) Solaris again, but it would take a lot of time. (5 Replies)
Discussion started by: orange47
5 Replies
7. UNIX for Dummies Questions & Answers
I'm trying to count the number of directories in a folder but I don't want to count the sub directories.
So far I have this:
find -type d | wc -l
Is there a parameter to stop counting sub directories ?
Thanks (5 Replies)
Discussion started by: Ultima
5 Replies
8. Red Hat
Hi,
I am trying to find the number of cache misses that are caused by my code. The best way I could find was to use the perf command. After running command: perf stat dd if=/dev/zero of=/dev/null count=100, the output I got is:
1.812057 task-clock-msecs # 0.876 CPUs
... (0 Replies)
Discussion started by: fidelity
0 Replies
9. Shell Programming and Scripting
I am trying to run following script in ksh on darwin 11.4.2:
freeSpace=2469606195
spaceNeeded=200
] && echo "no space" || echo "space available"
] && echo "no space" || echo "space available"
"-lt" is giving wrong answer as "no space" Whereas '<' works fine. When I change the freespace... (4 Replies)
Discussion started by: sabitha
4 Replies
10. Red Hat
Scenario:
1. Log into a linux server interface as root.
2. Inititiate an SSH session with the server using Putty and a valid user account (e.g. fakeuser).
3. Log into TTY2 of the linux server interface using another valid user account (e.g. faketester).
Issue:
With these three login... (1 Reply)
Discussion started by: walterthered
1 Replies
LEARN ABOUT CENTOS
reporter-mailx
REPORTER-MAILX(1) LIBREPORT MANUAL REPORTER-MAILX(1)
NAME
reporter-mailx - Sends contents of a problem directory via email.
SYNOPSIS
reporter-mailx [-v] -d DIR [-c CONFFILE]
DESCRIPTION
The tool reads a problem directory, composes an email message from the directory contents, and uses mailx to send the message to specified
recipient.
Properties of email messages can be specified in a configuration file, and via environment variables.
Configuration file
Configuration file contains entries in a format "Option = Value".
The options are:
Subject
The subject of the email message.
EmailFrom
The sender of the email message.
EmailTo
The recipient of the email message.
SendBinaryData
Use yes/true/on/1 to attach all binary files from the problem directory to the email. This can cause the emails to be very large.
Integration with ABRT events
reporter-mailx can be used as a reporter, to allow users report problems via email when they decide to do it. This usage is pre-configured
in /etc/libreport/events.d/mailx_event.conf:
EVENT=report_Mailx reporter-mailx
It can also be used to notify administrator automatically when a problem happens. When this is desired, modify the event configuration file
to run the tool on the post-create event:
EVENT=post-create reporter-mailx
OPTIONS
-d DIR
Path to problem directory.
-c CONFFILE
Path to configuration file. When used in ABRT event system, the file contains site-wide configuration. Users can change the values via
environment variables.
ENVIRONMENT VARIABLES
Environment variables take precedence over values provided in the configuration file.
Mailx_Subject
Subject of the email message.
Mailx_EmailFrom
Sender of the email message.
Mailx_EmailTo
Recipient of the email message. If nor the environment variable nor the corresponding option is defined, the message is send to
"root@localhost".
Mailx_SendBinaryData
Use yes/true/on/1 to attach all binary files from the problem directory to the email.
AUTHORS
o ABRT team
LIBREPORT 2.1.11 06/18/2014 REPORTER-MAILX(1)