04-08-2006
Number of posts counted wrong
I am not sure if this is the right place to post this. Heres my problem: When I posted yesterday I think I saw the number of posts made by me as above 60. Today morning when I posted, it showed my post as the 60th post. What went wrong? (In fact I referred to a previous post made me...it shows up as 60 too! So, now, I have two 60th posts)
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi ,
I am using SUN OS Version 5.6.
I have a file that contains records of length 270. when I do 'set nu' in vi editor, I get the count as 86. whereas when I do "wc -l" on the command prompt, it shows the count as only 85. this is very strange. why would the 'wc' show 1 record less. The job... (3 Replies)
Discussion started by: tselvanin
3 Replies
2. Filesystems, Disks and Memory
I had a power outage a day ago and when the power came back on my FreeBSD 4.6 webserver had problems. It said it was unable to mount /var and made me start in single user mode and said to run fsck MANUALY. So i did and this is now what i get.
www# fsck /dev/ad0s1e
** /dev/ad0s1e
BAD SUPER... (4 Replies)
Discussion started by: matthewbane
4 Replies
3. Solaris
/pci@if,0/pci@1,1/ide@3/dad@0,0 corrupt label wrong magic number
can u plz suggustion me (6 Replies)
Discussion started by: tirupathi
6 Replies
4. Filesystems, Disks and Memory
Whenever i run,
# fsck -F ufs /dev/dsk/c0t0d0s7
The following error prompt out:-
** /dev/dsk/c0t0d0s7
BAD SUPER BLOCK: MAGIC NUMBER WRONG
USE AN ALTERNATE SUPER-BLOCK TO SUPPLY NEEDED INFORMATION;
eg. fsck -o b=#
where # is the alternate super block. SEE fsck_ufs(1M).
... (3 Replies)
Discussion started by: beginningDBA
3 Replies
5. Solaris
I have created 1 LUN.
1)LUN 00BB 200GB /dev/rdsk/c1t3d44
/dev/rdsk/c2t28d44
/dev/rdsk/c3t19d44
/dev/rdsk/c4t12d44
2) Already added the new entry into sd.conf and rebooted.
3) Already done these:
powercf –q
power config
4) power display dev=all
I can see the new Symmetrix device.... (1 Reply)
Discussion started by: sirius20d
1 Replies
6. Solaris
Is there a way to recover label?
I could install (sparc) Solaris again, but it would take a lot of time. (5 Replies)
Discussion started by: orange47
5 Replies
7. UNIX for Dummies Questions & Answers
I'm trying to count the number of directories in a folder but I don't want to count the sub directories.
So far I have this:
find -type d | wc -l
Is there a parameter to stop counting sub directories ?
Thanks (5 Replies)
Discussion started by: Ultima
5 Replies
8. Red Hat
Hi,
I am trying to find the number of cache misses that are caused by my code. The best way I could find was to use the perf command. After running command: perf stat dd if=/dev/zero of=/dev/null count=100, the output I got is:
1.812057 task-clock-msecs # 0.876 CPUs
... (0 Replies)
Discussion started by: fidelity
0 Replies
9. Shell Programming and Scripting
I am trying to run following script in ksh on darwin 11.4.2:
freeSpace=2469606195
spaceNeeded=200
] && echo "no space" || echo "space available"
] && echo "no space" || echo "space available"
"-lt" is giving wrong answer as "no space" Whereas '<' works fine. When I change the freespace... (4 Replies)
Discussion started by: sabitha
4 Replies
10. Red Hat
Scenario:
1. Log into a linux server interface as root.
2. Inititiate an SSH session with the server using Putty and a valid user account (e.g. fakeuser).
3. Log into TTY2 of the linux server interface using another valid user account (e.g. faketester).
Issue:
With these three login... (1 Reply)
Discussion started by: walterthered
1 Replies
LEARN ABOUT FREEBSD
pgsignal
PSIGNAL(9) BSD Kernel Developer's Manual PSIGNAL(9)
NAME
psignal, pgsignal, gsignal, tdsignal -- post signal to a thread, process, or process group
SYNOPSIS
#include <sys/types.h>
#include <sys/signalvar.h>
void
psignal(struct proc *p, int signum);
void
pgsignal(struct pgrp *pgrp, int signum, int checkctty);
void
gsignal(int pgid, int signum);
void
tdsignal(struct thread *td, int signum);
DESCRIPTION
These functions post a signal to a thread or one or more processes. The argument signum common to all three functions should be in the range
[1-NSIG].
The psignal() function posts signal number signum to the process represented by the process structure p. With a few exceptions noted below,
the target process signal disposition is updated and is marked as runnable, so further handling of the signal is done in the context of the
target process after a context switch. Note that psignal() does not by itself cause a context switch to happen.
The target process is not marked as runnable in the following cases:
o The target process is sleeping uninterruptibly. The signal will be noticed when the process returns from the system call or trap.
o The target process is currently ignoring the signal.
o If a stop signal is sent to a sleeping process that takes the default action (see sigaction(2)), the process is stopped without
awakening it.
o SIGCONT restarts a stopped process (or puts them back to sleep) regardless of the signal action (e.g., blocked or ignored).
If the target process is being traced psignal() behaves as if the target process were taking the default action for signum. This allows the
tracing process to be notified of the signal.
The pgsignal() function posts signal number signum to each member of the process group described by pgrp. If checkctty is non-zero, the sig-
nal will be posted only to processes that have a controlling terminal. pgsignal() is implemented by walking along the process list headed by
the field pg_members of the process group structure pointed at by pgrp and calling psignal() as appropriate. If pgrp is NULL no action is
taken.
The gsignal() function posts signal number signum to each member of the process group identified by the group id pgid. gsignal() first finds
the group structure associated with pgid, then invokes pgsignal() with the argument checkctty set to zero. If pgid is zero no action is
taken.
The tdsignal() function posts signal number signum to the thread represented by the thread structure td.
SEE ALSO
sigaction(2), signal(9), tsleep(9)
BSD
October 8, 2011 BSD