04-08-2006
Number of posts counted wrong
I am not sure if this is the right place to post this. Heres my problem: When I posted yesterday I think I saw the number of posts made by me as above 60. Today morning when I posted, it showed my post as the 60th post. What went wrong? (In fact I referred to a previous post made me...it shows up as 60 too! So, now, I have two 60th posts)
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi ,
I am using SUN OS Version 5.6.
I have a file that contains records of length 270. when I do 'set nu' in vi editor, I get the count as 86. whereas when I do "wc -l" on the command prompt, it shows the count as only 85. this is very strange. why would the 'wc' show 1 record less. The job... (3 Replies)
Discussion started by: tselvanin
3 Replies
2. Filesystems, Disks and Memory
I had a power outage a day ago and when the power came back on my FreeBSD 4.6 webserver had problems. It said it was unable to mount /var and made me start in single user mode and said to run fsck MANUALY. So i did and this is now what i get.
www# fsck /dev/ad0s1e
** /dev/ad0s1e
BAD SUPER... (4 Replies)
Discussion started by: matthewbane
4 Replies
3. Solaris
/pci@if,0/pci@1,1/ide@3/dad@0,0 corrupt label wrong magic number
can u plz suggustion me (6 Replies)
Discussion started by: tirupathi
6 Replies
4. Filesystems, Disks and Memory
Whenever i run,
# fsck -F ufs /dev/dsk/c0t0d0s7
The following error prompt out:-
** /dev/dsk/c0t0d0s7
BAD SUPER BLOCK: MAGIC NUMBER WRONG
USE AN ALTERNATE SUPER-BLOCK TO SUPPLY NEEDED INFORMATION;
eg. fsck -o b=#
where # is the alternate super block. SEE fsck_ufs(1M).
... (3 Replies)
Discussion started by: beginningDBA
3 Replies
5. Solaris
I have created 1 LUN.
1)LUN 00BB 200GB /dev/rdsk/c1t3d44
/dev/rdsk/c2t28d44
/dev/rdsk/c3t19d44
/dev/rdsk/c4t12d44
2) Already added the new entry into sd.conf and rebooted.
3) Already done these:
powercf –q
power config
4) power display dev=all
I can see the new Symmetrix device.... (1 Reply)
Discussion started by: sirius20d
1 Replies
6. Solaris
Is there a way to recover label?
I could install (sparc) Solaris again, but it would take a lot of time. (5 Replies)
Discussion started by: orange47
5 Replies
7. UNIX for Dummies Questions & Answers
I'm trying to count the number of directories in a folder but I don't want to count the sub directories.
So far I have this:
find -type d | wc -l
Is there a parameter to stop counting sub directories ?
Thanks (5 Replies)
Discussion started by: Ultima
5 Replies
8. Red Hat
Hi,
I am trying to find the number of cache misses that are caused by my code. The best way I could find was to use the perf command. After running command: perf stat dd if=/dev/zero of=/dev/null count=100, the output I got is:
1.812057 task-clock-msecs # 0.876 CPUs
... (0 Replies)
Discussion started by: fidelity
0 Replies
9. Shell Programming and Scripting
I am trying to run following script in ksh on darwin 11.4.2:
freeSpace=2469606195
spaceNeeded=200
] && echo "no space" || echo "space available"
] && echo "no space" || echo "space available"
"-lt" is giving wrong answer as "no space" Whereas '<' works fine. When I change the freespace... (4 Replies)
Discussion started by: sabitha
4 Replies
10. Red Hat
Scenario:
1. Log into a linux server interface as root.
2. Inititiate an SSH session with the server using Putty and a valid user account (e.g. fakeuser).
3. Log into TTY2 of the linux server interface using another valid user account (e.g. faketester).
Issue:
With these three login... (1 Reply)
Discussion started by: walterthered
1 Replies
LEARN ABOUT DEBIAN
blaze-remove
BLAZE-REMOVE(1) BlazeBlogger Documentation BLAZE-REMOVE(1)
NAME
blaze-remove - removes a post or page from the BlazeBlogger repository
SYNOPSIS
blaze-remove [-fipqPV] [-b directory] id...
blaze-remove -h|-v
DESCRIPTION
blaze-remove removes a blog post or a page with the specified id from the BlazeBlogger repository.
OPTIONS
-b directory, --blogdir directory
Allows you to specify a directory in which the BlazeBlogger repository is placed. The default option is a current working directory.
-p, --page, --pages
Tells blaze-remove to remove a page or pages.
-P, --post, --posts
Tells blaze-remove to remove a blog post or blog posts. This is the default option.
-f, --force
Disables requiring manual confirmation of each blog post or page removal. This is the default option.
-i, --interactive
Enables requiring manual confirmation of each blog post or page removal.
-q, --quiet
Disables displaying of unnecessary messages.
-V, --verbose
Enables displaying of all messages. This is the default option.
-h, --help
Displays usage information and exits.
-v, --version
Displays version information and exits.
EXAMPLE USAGE
Remove a blog post:
~]$ blaze-remove 10
Successfully removed the post with ID 10.
Remove a page:
~]$ blaze-remove -p 4
Successfully removed the page with ID 4.
Remove multiple blog posts:
~]$ blaze-remove 10 4 6
Successfully removed the post with ID 10, 4 and 6.
Remove multiple blog posts safely:
~]$ blaze-remove -i 10 4 6
Remove the post with ID 10 titled `Debian and Fedora Packages'? y
Remove the post with ID 4 titled `BlazeBlogger 0.8.0 RC2'? y
Remove the post with ID 6 titled `BlazeBlogger 0.8.1'? y
Successfully removed the post with ID 10, 4 and 6.
SEE ALSO
blaze-config(1), blaze-add(1), blaze-list(1)
BUGS
To report a bug or to send a patch, please, add a new issue to the bug tracker at <http://code.google.com/p/blazeblogger/issues/>, or visit
the discussion group at <http://groups.google.com/group/blazeblogger/>.
COPYRIGHT
Copyright (C) 2008-2011 Jaromir Hradilek
This program is free software; see the source for copying conditions. It is distributed in the hope that it will be useful, but WITHOUT ANY
WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
Version 1.2.0 2012-03-05 BLAZE-REMOVE(1)