|
|
Sponsored Content
Top Forums
UNIX for Advanced & Expert Users
Port Redundancy
Post 302070187 by Frank2004 on Sunday 2nd of April 2006 11:49:41 PM
04-03-2006
|
|
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I'm trying to come up with an "imaging" type solution (a.k.a. Norton Ghost, Imagecast) with standard unix utils. I'd like to just image one of our FreeBSD servers so I can use the hot swap HD's. If one fails, I could slide in an exact duplicate HD and the server would be back up. I've tried just... (4 Replies)
Discussion started by: mstevenson
4 Replies
2. UNIX for Advanced & Expert Users
Here we want to implement the network redundancy on UNIX with the software.
The two network interface cards are configured on the UNIX node,once one card is down or unnormal,the other can take over. Those aplications that used the tcp ,udp,multicast protocol can also been switched at the same... (2 Replies)
Discussion started by: Frank2004
2 Replies
3. Shell Programming and Scripting
Hi I have a file in which there are lot of redundancy messages..
Like suppose i have the messages like the following in my file..
45123|1|784tryr|uirirr|wagras|swyuyau||
45123|1|784tryr|uirirr|wagras|swyuyau||
I need to remove the extra (45123|1|784tryr|uirirr|wagras|swyuyau||) and need... (1 Reply)
Discussion started by: grajesh_955
1 Replies
4. UNIX for Dummies Questions & Answers
We have had some email outages in the last few months and my boss is asking is it worth going with one of those email redundancy/filtering sites. The thing is, we have a backup server on a remote location, so I am pretty sure we can set something up with what we have already.
At the moment... (1 Reply)
Discussion started by: edzillion
1 Replies
5. AIX
Hi Guys,
I'm working on building a new 595 machine.. I'm try to achieve high availability for the VIO clients using 2 VIO servers, The ethernet part is satisfied using SEA failover, Now how do I achieve redundancy for the disks, its the servers internal disk attached to the scsi cards...
... (2 Replies)
Discussion started by: kkeng808
2 Replies
6. AIX
Have been learning a lot off late and am a little unclear about the VIOS setup particularly with regards to redundancy. Would appreciate your help.
My question is very basic. Lets say I have setup a VIOS and 3 LPARs on only one hdd (non scsi). On what do I setup the second VIOS? Could I for... (7 Replies)
Discussion started by: theaixeman
7 Replies
7. AIX
I have one p5 server, no lpar, 2 physical network adapter, bundle as one EtherChannel. The two 2 physical network adapter connect to 2 network switches.
How to make this as a redundancy config?
Current is if one physical network adapter down, the seond one will go through the network. but if... (2 Replies)
Discussion started by: rainbow_bean
2 Replies
8. UNIX for Dummies Questions & Answers
Hi Everyone,
I've been using awk '!x++' to get rid of redundancy in a file, but it's getting rid of some extra lines I need (like the plus signs in the example below).
So how would I go from this:
@XYZ
ABCD
345345
+
@MNO
EFGH
789789
+
@XYZ
ABCD
345345
+
to: (2 Replies)
Discussion started by: sp24
2 Replies
9. Solaris
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
LEARN ABOUT SUNOS
chs
chs(7D) Devices chs(7D) NAME
chs - IBM ServeRAID PCI host adapter driver DESCRIPTION
The chs driver is the IBM ServeRAID PCI controller driver. PRECONFIGURATION
Known Problems and Limitations To prevent data loss, a SCSI disk drive that is not defined as part of any physical pack within a logical drive will not be accessible through the Solaris operating environment. CONFIGURATION
Auto-configuration code determines whether the adapter is present at the configured address and what types of devices are attached to it. The IBM ServeRAID is primarily used as a disk array (system drive) controller. To configure the attached disk arrays, you must configure the controller (using the configuration utilities provided by the hardware manu- facturer) before booting the Solaris operating environment You use the configuration utilities to set RAID levels, stripe parameters, cache mechanisms and perform other functions. For more information, see the user manual supplied with your hardware. FILES
/kernel/drv/chs.conf chs configuration file /dev/dsk/cndn[s|p]n block device /dev/rdsk/cndn[s|p]n raw device where: cn controller n dn LUN n (0-7) sn UNIX system slice n (0-15) pn fdisk(1M) partition(0) ATTRIBUTES
See attributes(5) for a description of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | |Architecture |x86 | +-----------------------------+-----------------------------+ SEE ALSO
fdisk(1M), attributes(5), cmdk(7D) SunOS 5.10 27 November 2000 chs(7D)