03-29-2006
Anyone???
I'm getting desparate!!!
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
we have a problem with a server UNIX SUN OS 5.7 :
we tried to reboot it and we have the following error message :
"boot load failed
the file just loaded does not appear to be executable "
we booted the server in single user mode with the cdrom
we made the mirrored disk bootable
we tried... (2 Replies)
Discussion started by: farzolito
2 Replies
2. UNIX for Advanced & Expert Users
Hi All.
Yesterday my pc worked fine. Today when booting the sequence gets just past mounting the root filesystem - it then says
' Module dependencies up to date (no new kernel modules found).'
At this point it hangs and goes no further! Does this sound familiar to anyone?
I am running... (2 Replies)
Discussion started by: silvaman
2 Replies
3. UNIX for Advanced & Expert Users
Hey !
I am running EWS-UX/V (Rel 4.2) on NEC EWS/4800/330 station and I am having problems rebooting my station : I am getting the following message on display : BOOT : PANIC : File size out of range.
According to user guide, this error is occuring when a file exceeding the limit and/or... (2 Replies)
Discussion started by: fredo
2 Replies
4. Solaris
When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error.
cannot find mis/krtld
boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies
5. Solaris
Hi everyone,
I have sun fire280R machine before i it is installed with solaris5.9 now i want to upgrade it but it not booting from the cd rom ....OK prompt also not comming i dont have solaris keyboard to press stop-A key...i have a intel supported keyboard ...what may be the problem it is... (1 Reply)
Discussion started by: alakshmanrao
1 Replies
6. SCO
Hi i have a problem after boot with N1 disk and putting N2 disk and pressing the enter in this message:Insert N2(filesystem) floppy and press after by this(pressing enter) the system is reboot!! why??? :confused:
my old pc is a Pentium II 333mhz 3gb hd 64mb ram
please help!! :( (3 Replies)
Discussion started by: panos_pit
3 Replies
7. UNIX for Dummies Questions & Answers
hello
i have a sun server V890 and it stops booting after adding 2 CPUs modules and gives me the following error message:
Enabling system bus....... Done
Initializing CPUs......... Done
Initializing boot memory..
RAM-Copy CRC failure!Can't start: No image found
FATAL: Can't find/decompress... (0 Replies)
Discussion started by: bahjatm
0 Replies
8. Solaris
hello
i have a sun server V890 and it stops booting after adding 2 CPUs modules and gives me the following error message:
Enabling system bus....... Done
Initializing CPUs......... Done
Initializing boot memory..
RAM-Copy CRC failure!Can't start: No image found
FATAL: Can't find/decompress... (12 Replies)
Discussion started by: bahjatm
12 Replies
9. Solaris
Hi all,
I have the the following SCSI diagnostic codes shown in the attached photo
I suspect disk drive failure what can I do further to diagnose the disk. and if possible to boot into OS again. (5 Replies)
Discussion started by: h@foorsa.biz
5 Replies
10. UNIX for Dummies Questions & Answers
UNIX sco release 5.05 system does not boot:cannot open device hd(40)/boot
stage 1 boot failure: error loading hd(40)/bootWhat to do? (2 Replies)
Discussion started by: Joaoalpande
2 Replies
AHB(4) BSD Kernel Interfaces Manual AHB(4)
NAME
ahb -- Adaptec EISA SCSI host adapter driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device ahb
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
ahb_load="YES"
DESCRIPTION
This driver provides access to the SCSI bus connected to an Adaptec AHA-174X host adapters in ``enhanced'' mode. Tagged queueing and syn-
chronous SCSI transfers are supported.
HARDWARE
The ahb driver supports the following SCSI host adapters:
o Adaptec AHA-1740
o Adaptec AHA-1742
o Adaptec AHA-1740A
o Adaptec AHA-1742A
SEE ALSO
aha(4), ahc(4), aic(4), cd(4), da(4), sa(4), scsi(4)
AUTHORS
The ahb driver was written by Justin T. Gibbs.
CAVEATS
The Adaptec 174X is very sensitive to SCSI bus termination and cable length. It may also have difficulties operating with some modern
devices that, due to their speed, expose timing problems in the controller. There are no known mechanisms for working around device incom-
patibilities of this nature.
BSD
July 4, 2004 BSD