03-28-2006
Specifying network configuration info
Can someone please point me in the correct direction of where I configure the network information on SunOS 5.8 server? (Searching SunSolve and Google have resulted in thousands of fixes for potential errors, but I can't find the general instructions, etc. for starting the process).
Thanks!
10 More Discussions You Might Find Interesting
1. HP-UX
Hi,
I have installed a HP-UX B.11.00 U 9000/800 Server in one of the domain. And I'm also able to telnet/ping into this server from systems in the same domain.
But I'm not able to telnet/ping into this server from a different domain.
So, what shoud need to do to achieve this... (6 Replies)
Discussion started by: S.Vishwanath
6 Replies
2. Solaris
hi again...
i configured my network settings sometiime ago using the sys-unconfig command.the active link was rtls0.
there was some problem with the network so i changed the ISP. now when im trying to reconfigure the system wit sys-unconfig, it tries to configure the network on rtls1 (and shows... (1 Reply)
Discussion started by: strider
1 Replies
3. Linux
Hello everybody,
How can link network interface to the output of lspci -vv. Basicly i need to know who is the manufacturer of a specific interface, for example eth0 {Is it an Intel, or Broadcome, or something else}. Is there a way to find that out?
Thanx (5 Replies)
Discussion started by: aleksey
5 Replies
4. AIX
hi all,
how do i change the routing info and make sure i will be able to connect remotely?
any ideas please?
thanks in advance. (1 Reply)
Discussion started by: itik
1 Replies
5. SCO
I have a SCO 5.07 Server and I am trying to get it on my network. I have edited the /etc/hosts file and /etc/rc2.d/s99route . I has connectivity on the NIC card but not sure if I am forgetting another file. Thanks! (2 Replies)
Discussion started by: andrewd
2 Replies
6. UNIX for Dummies Questions & Answers
I am using solaris 10, my internet works alright but each time i reboot i keep loosing my connection. I will have to use the
ifconfig iprb0 192.168.1.xx netmask 255.255.255.0 up and
Route add default 192.168.1.xxx command to gain back my internet.
I know there is a better way of addressing... (1 Reply)
Discussion started by: seyiisq
1 Replies
7. Solaris
Hi
I have installed Solaris 5.10 on Intel x86 machine (standalone).
I want to access internet through solaris. How should I configure the network? Is static IP or DHCP advisable? (5 Replies)
Discussion started by: johnl
5 Replies
8. UNIX and Linux Applications
In gnome there was an indicator applet that displayed your ip address, subnet mask, gateway, and dns. Is there a similar applet in kde? (0 Replies)
Discussion started by: cokedude
0 Replies
9. UNIX for Advanced & Expert Users
Is there a command that display all network info. I'm looking for ip address, subnet mask, gateway, and dns. If there isn't a single command could someone please write me a shellscript that can do this? (8 Replies)
Discussion started by: cokedude
8 Replies
10. UNIX for Dummies Questions & Answers
Hi,
Need to Collect IP Details in the following format
ServerName ; IPADDR1 ; NETMASK1 ; IPADDR2 ; NETMASK2 ; IPADDR3 ; NETMASK3 ;
Could you please give me the suggesstions.
Thanks (1 Reply)
Discussion started by: rajasekg
1 Replies
LEARN ABOUT REDHAT
ipx_cmd
IPX_CMD(8) System Manager's Manual IPX_CMD(8)
NAME
ipx_cmd - bridge between Novell's SCMD driver and local IPX network
SYNOPSIS
ipx_cmd -A server name [ -l local interface name ]
DESCRIPTION
ipx_cmd moves packets from tapN to server and vice versa. It is something like IPX Tunnel, but it uses Novell Netware 5 server Compatibil-
ity Mode Driver (AKA Migration Agent) on the other end of wire. You must first configure your kernel tapN device with IPX EthernetII frame
and with network number set up on server (you can use kernel autodetection).
OPTIONS
-A server name
This is IP name of compatibility mode server. You can use DNS name or dotted quad to specify server address.
-l local interface name
This allows you to specify, which of your IP addresses should be used as IP address of client side of CMD driver. You must configure
your tapN device with hardware address 7E:01:AA:BB:CC:DD, where AA:BB:CC:DD is your IP address in hexa.
EXAMPLE
If you are on server platan.vc.cvut.cz (147.32.240.81) and your migration agent runs on server boris.vc.cvut.cz, you can configure your
system with:
insmod ethertap
ifconfig tap0 hw ether 7E:01:93:20:F0:51 up
ipx_interface add -p tap0 EtherII
ipx_cmd -A boris.vc.cvut.cz -l 147.32.240.81 &
BUGS
This program was written to satisfy my own needs and should be really improved. At least it should configure tap interface itself.
AUTHOR
Petr Vandrovec <vandrove@vc.cvut.cz>
ipx_cmd IPX Utilities IPX_CMD(8)