|
|
Sponsored Content
Top Forums
UNIX for Advanced & Expert Users
nslookup problem
Post 302069084 by xnightcrawl on Wednesday 22nd of March 2006 02:02:27 PM
03-22-2006
db.192.168.1
that is the zone file. 
Last edited by xnightcrawl; 05-01-2006 at 06:32 PM..
|
|
10 More Discussions You Might Find Interesting
1. Solaris
I don't have DNS, and would like to resolve EVERYTHING through local /etc/hosts file.
My first sunbox has the following configuration:
# hostname
mybox.home.com
My host file is as follows:
# cat /etc/hosts
#
# Internet host table
#
127.0.0.1 localhost
192.25.x.x ... (6 Replies)
Discussion started by: mr_manny
6 Replies
2. IP Networking
hi,
what would cause the nslookup to work one way but not the other?
for most machine it works both ways.
>nslookup 172.18.10.235
Server: 172.16.17.3
Address: 172.16.17.3#53
235.10.18.172.in-addr.arpa name = machine1.prod.local
>nslookup machine1
Server: ... (3 Replies)
Discussion started by: purest
3 Replies
3. Shell Programming and Scripting
Hi All,
If I give the hostname followed by nslookup, I get the output like below,
commandprompt>nslookup efgh
Using /etc/hosts on: xyz
looking up FILES
Trying DNS
Non-authoritative answer:
Name: abcd
Address: 47.47.47.47
Aliases: efgh
I am not sure on the bolded ones. Can... (4 Replies)
Discussion started by: Rajakct84
4 Replies
4. Solaris
Hi ,
I have a requirement to find the aliases by doing an nslookup on the Cname.
If i do an nslookup on the alias name i get the Cname , but i need the cname from alias name.
eg: Hostname = acb.example.com
Virtual name= abcvirtual.example.com
nslookup abcvirtual.example.com will... (3 Replies)
Discussion started by: mpics66
3 Replies
5. Shell Programming and Scripting
Hi guys,
I'm back to get some help again :)
I have a file that has a list of IP addresses, and I use nslookup in my script to resolve hostnames of those IPs.
the problem I'm facing is that I not all the hostnames got resolved! and I don't know why. sometimes the same duplicate IP returns a... (8 Replies)
Discussion started by: Abdulelah
8 Replies
6. Emergency UNIX and Linux Support
Hi all
Nslookup command returns!!!!
Code:
nslookup 10.91.44.29
Server: 127.0.0.1
Address: 127.0.0.1#53
29.44.91.in-addr.arpa name = station1.example.com
Code:
nslookup station1.example.com
Server: 127.0.0.1
Address: 127.0.0.1#53
Name: ... (4 Replies)
Discussion started by: anishkumarv
4 Replies
7. HP-UX
I am having a problem with a new server build that has got me completely baffled. This server has a private back end network so the way it is supposed to work is that the server thinks its ip address is 10.131.0.48 but the rest of the world knows it as 199.68.100.100 per DNS. It has to be this way... (2 Replies)
Discussion started by: keelba
2 Replies
8. Solaris
hi,
I am new in Solaris 10 , i am installing a software in solaris 10, while performing pre requisite nslookup command should return without error, and the IP address and host should match those listed in the etc/hosts file,
but nslookup command show the below error , can anybody tell me how i... (4 Replies)
Discussion started by: zeeshan047
4 Replies
9. Shell Programming and Scripting
Hey folks. Long time lurker, first time poster. I'm a bit of a newbie at "coding" (obviously, scripting is a teensy bit different than coding) and I've run into a problem that I just can't seem to get around.
I'm going through a list of servers to check their name, IP, reverse-NSLOOKUP name and... (2 Replies)
Discussion started by: Bearwhale
2 Replies
10. Shell Programming and Scripting
Hi,
I have a rather simple awk statement to perform an nslookup on a file (list of IPs). If the lookup yields a result, then it sends it to a file. If no result, there is no output. I've been trying to use !NR or !NF with an if statement to make the output state "NA" if there is no result,... (5 Replies)
Discussion started by: umang2382
5 Replies
LEARN ABOUT SUNOS
named-checkzone
named-checkzone(1M) System Administration Commands named-checkzone(1M) NAME
named-checkzone - zone file validity checking tool SYNOPSIS
named-checkzone [-djqv] [-c class] zonename filename DESCRIPTION
The named-checkzone utility checks the syntax and integrity of a zone file. It performs the same checks as named(1M) does when loading a zone. The named-checkzone utility is useful for checking zone files before configuring them into a name server. OPTIONS
The following options are supported: -c class Specify the class of the zone. If not specified, "IN" is assumed. -d Enable debugging. -j Read the journal, if it exists, when loading the zone file. -q Run in quiet mode, reporting only the exit status. -v Print the version of the named-checkzone program and exit. OPERANDS
The following operands are supported: filename The name of the zone file. zonename The domain name of the zone being checked. EXIT STATUS
0 No errors were detected. 1 An error was detected. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | |Availability |SUNWbind9 | |Interface Stability |External | +-----------------------------+-----------------------------+ SEE ALSO
named(1M), attributes(5) RFC 1035 BIND 9 Administrator Reference Manual NOTES
Source for BIND9 is available in the SUNWbind9S package. SunOS 5.10 15 Dec 2004 named-checkzone(1M)