03-21-2006
Not sure if this is what you can use or not -
modinfo command (search for modinfo in that page).
Plus, I don't know how you would check if the version this shows is 'up to date'.
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. UNIX for Dummies Questions & Answers
1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface,
2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
Discussion started by: gops
1 Replies
3. IP Networking
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
Discussion started by: DPAI
0 Replies
4. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
5. UNIX for Advanced & Expert Users
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies
6. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
7. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
8. UNIX for Advanced & Expert Users
Is there a command that display all network info. I'm looking for ip address, subnet mask, gateway, and dns. If there isn't a single command could someone please write me a shellscript that can do this? (8 Replies)
Discussion started by: cokedude
8 Replies
9. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
10. Ubuntu
Hi
Please can you help me to understand what could be wrong based on what I have captured in the logs:
I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed.
Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies
LEARN ABOUT DEBIAN
io::all::http
IO::All::HTTP(3pm) User Contributed Perl Documentation IO::All::HTTP(3pm)
NAME
IO::All::LWP - Extends IO::All to HTTP URLs
SYNOPSIS
use IO::All;
$content < io('http://example.org'); # GET webpage into scalar
io('http://example.org') > io('index.html'); # GET to file
"hello
" > io('http://example.org/index.html'); # PUT webpage
# two ways of getting a page with a password:
$content < io('http://me:secret@example.org');
$content < io('http://example.org')->user('me')->password('secret');
DESCRIPTION
This module extends IO::All for dealing with HTTP URLs. Note that you don't need to use it explicitly, as it is autoloaded by IO::All
whenever it sees something that looks like an HTTP URL.
The SYNOPSIS shows some simple typical examples, but there are many other interesting combinations with other IO::All features! For
example, you can get an HTTP URL and write the content to a socket, or to an FTP URL, of to a DBM file.
METHODS
This is a subclass of IO::All::LWP. The only new method is "http", which can be used to create a blank IO::All::HTTP object; or it can also
take an HTTP URL as a parameter. Note that in most cases it is simpler just to call io('http://example.com'), which calls the "http" method
automatically.
OPERATOR OVERLOADING
The same operators from IO::All may be used. < GETs an HTTP URL; > PUTs to an HTTP URL.
SEE ALSO
IO::All, IO::All::LWP, LWP.
AUTHORS
Ivan Tubert-Brohman <itub@cpan.org> and Brian Ingerson <ingy@cpan.org>
COPYRIGHT
Copyright (c) 2007. Ivan Tubert-Brohman and Brian Ingerson. All rights reserved.
This program is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
See <http://www.perl.com/perl/misc/Artistic.html>
perl v5.10.0 2007-03-29 IO::All::HTTP(3pm)