Sponsored Content
Full Discussion: Unix Boot up problem
Top Forums UNIX for Dummies Questions & Answers Unix Boot up problem Post 302068596 by Neo on Sunday 19th of March 2006 11:16:33 AM
Old 03-19-2006
I think you mean "disk space" not "memory" in the root directory. You might try posting the output of your df command.
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Boot problem

we have a problem with a server UNIX SUN OS 5.7 : we tried to reboot it and we have the following error message : "boot load failed the file just loaded does not appear to be executable " we booted the server in single user mode with the cdrom we made the mirrored disk bootable we tried... (2 Replies)
Discussion started by: farzolito
2 Replies

2. UNIX for Advanced & Expert Users

Boot Problem

Hi All. Yesterday my pc worked fine. Today when booting the sequence gets just past mounting the root filesystem - it then says ' Module dependencies up to date (no new kernel modules found).' At this point it hangs and goes no further! Does this sound familiar to anyone? I am running... (2 Replies)
Discussion started by: silvaman
2 Replies

3. UNIX for Advanced & Expert Users

Cannot boot - Boot : Panic : File size out of range (EWS-UX/V unix)

Hey ! I am running EWS-UX/V (Rel 4.2) on NEC EWS/4800/330 station and I am having problems rebooting my station : I am getting the following message on display : BOOT : PANIC : File size out of range. According to user guide, this error is occuring when a file exceeding the limit and/or... (2 Replies)
Discussion started by: fredo
2 Replies

4. Solaris

solaris boot problem boot error loading interpreter(misc/krtld)

When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error. cannot find mis/krtld boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies

5. Solaris

Boot problem

Hi everyone, I have sun fire280R machine before i it is installed with solaris5.9 now i want to upgrade it but it not booting from the cd rom ....OK prompt also not comming i dont have solaris keyboard to press stop-A key...i have a intel supported keyboard ...what may be the problem it is... (1 Reply)
Discussion started by: alakshmanrao
1 Replies

6. SCO

Sco unix v/386 3.2 problem boot and install

Hi i have a problem after boot with N1 disk and putting N2 disk and pressing the enter in this message:Insert N2(filesystem) floppy and press after by this(pressing enter) the system is reboot!! why??? :confused: my old pc is a Pentium II 333mhz 3gb hd 64mb ram please help!! :( (3 Replies)
Discussion started by: panos_pit
3 Replies

7. UNIX for Dummies Questions & Answers

boot problem

hello i have a sun server V890 and it stops booting after adding 2 CPUs modules and gives me the following error message: Enabling system bus....... Done Initializing CPUs......... Done Initializing boot memory.. RAM-Copy CRC failure!Can't start: No image found FATAL: Can't find/decompress... (0 Replies)
Discussion started by: bahjatm
0 Replies

8. Solaris

boot problem

hello i have a sun server V890 and it stops booting after adding 2 CPUs modules and gives me the following error message: Enabling system bus....... Done Initializing CPUs......... Done Initializing boot memory.. RAM-Copy CRC failure!Can't start: No image found FATAL: Can't find/decompress... (12 Replies)
Discussion started by: bahjatm
12 Replies

9. Solaris

Boot problem

Hi all, I have the the following SCSI diagnostic codes shown in the attached photo I suspect disk drive failure what can I do further to diagnose the disk. and if possible to boot into OS again. (5 Replies)
Discussion started by: h@foorsa.biz
5 Replies

10. UNIX for Dummies Questions & Answers

Error UNIX: UNIX SCO release 5.05 system does not boot

UNIX sco release 5.05 system does not boot:cannot open device hd(40)/boot stage 1 boot failure: error loading hd(40)/bootWhat to do? (2 Replies)
Discussion started by: Joaoalpande
2 Replies
SYSTEMD-VOLATILE-ROOT.SERVICE(8)			   systemd-volatile-root.service			  SYSTEMD-VOLATILE-ROOT.SERVICE(8)

NAME
systemd-volatile-root.service, systemd-volatile-root - Make the root file system volatile SYNOPSIS
systemd-volatile-root.service /lib/systemd/systemd-volatile-root DESCRIPTION
systemd-volatile-root.service is a service that replaces the root directory with a volatile memory file system ("tmpfs"), mounting the original (non-volatile) /usr inside it read-only. This way, vendor data from /usr is available as usual, but all configuration data in /etc, all state data in /var and all other resources stored directly under the root directory are reset on boot and lost at shutdown, enabling fully stateless systems. This service is only enabled if full volatile mode is selected, for example by specifying "systemd.volatile=yes" on the kernel command line. This service runs only in the initial RAM disk ("initrd"), before the system transitions to the host's root directory. Note that this service is not used if "systemd.volatile=state" is used, as in that mode the root directory is non-volatile. SEE ALSO
systemd(1), systemd-fstab-generator(8), kernel-command-line(7) systemd 237 SYSTEMD-VOLATILE-ROOT.SERVICE(8)
All times are GMT -4. The time now is 12:43 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy