10-17-2002
Raid and multibooting
Hi all,
I'm about to reconfigure my system with Raid Level 0. I haven't been able to find out much about Raid and Linux through searching. I'll be multi-booting with Win 2K, XP, Mandrake 9 and Red Hat 8. I have 3 drives (2 X 60GB and 1 X 80GB) and want to use Raid 0 to configure the drives into 4 partitions of a little under 50GB each. Will Mandrake and Red Hat accept this Raid configuration ok, or should I config differently: leave 2K & XP on drives of their own and partition the 80 for the Linuxs, for example? Any recomendations would be appreciated greatly.
Regards
9 More Discussions You Might Find Interesting
1. Solaris
hai everybody n good morning........here r some queries.......
1. what is the interlace value in RAID 0 (striping.......)
2. How many no of metadevices are required for mirroring and why......... (1 Reply)
Discussion started by: sudhansu
1 Replies
2. Solaris
hi all...sudhansu here............ i need some help..........
what is RAID 0+1 and RAID 1+0.............what is the difference between them................
suppose i have 80 gb disk space,then which RAID level i follow n why......... i need redundancy n maximum storage..........please help (3 Replies)
Discussion started by: sudhansu
3 Replies
3. Solaris
Somebody can help me ! how can i do mirror in sun ver 8
without third party software !!! (3 Replies)
Discussion started by: goldfelda
3 Replies
4. UNIX for Dummies Questions & Answers
Hi
Can someone tell me what are the differences between software and hardware raid ?
thx for help. (2 Replies)
Discussion started by: presul
2 Replies
5. Solaris
Dear ALl,
I have a RAID 5 volume which is as below
d120 r 60GB c1t2d0s5 c1t3d0s5 c1t4d0s5 c1t5d0s5
d7 r 99GB c1t2d0s0 c1t3d0s0 c1t4d0s0 c1t5d0s0
d110 r 99GB c1t2d0s4 c1t3d0s4 c1t4d0s4 c1t5d0s4
d8 r 99GB c1t2d0s1 c1t3d0s1... (2 Replies)
Discussion started by: jegaraman
2 Replies
6. Solaris
Hello All,
I have read enough of texts on Raid 01 and Raid 10 on solaris :wall: . But no-where found a way to create them using SVM. Some one pls tell me how to do or Post some link if that helps.
TIA
Curious
solarister (1 Reply)
Discussion started by: Solarister
1 Replies
7. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
8. Solaris
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Discussion started by: KhawHL
4 Replies
9. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
MPT(4) BSD Kernel Interfaces Manual MPT(4)
NAME
mpt -- LSI Fusion-MPT SCSI/Fibre Channel driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device mpt
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
mpt_load="YES"
DESCRIPTION
The mpt driver provides support for the LSI Logic Fusion-MPT family of SCSI, Fibre Channel and SAS controllers.
HARDWARE
The following controllers are supported by the mpt driver:
o LSI Logic 53c1030, LSI Logic LSI2x320-X (Single and Dual Ultra320 SCSI)
o LSI Logic AS1064, LSI Logic AS1068 (SAS/SATA)
o LSI Logic FC909 (1Gb/s Fibre Channel)
o LSI Logic FC909A (Dual 1Gb/s Fibre Channel)
o LSI Logic FC919, LSI Logic 7102XP-LC (Single 2Gb/s Fibre Channel)
o LSI Logic FC929, LSI Logic FC929X, LSI Logic 7202XP-LC (Dual 2Gb/s Fibre Channel)
o LSI Logic FC949X (Dual 4Gb/s Fibre Channel)
o LSI Logic FC949E, LSI Logic FC949ES (Dual 4Gb/s Fibre Channel PCI-Express)
The Ultra 320 SCSI controller chips supported by the mpt driver can be found onboard on many systems including:
o Dell PowerEdge 1750 thru 2850
o IBM eServer xSeries 335
These systems also contain Integrated Raid Mirroring and Integrated Raid Mirroring Enhanced which this driver also supports.
The SAS controller chips are also present on many new AMD/Opteron based systems, like the Sun 4100. Note that this controller can drive both
SAS and SATA drives or a mix of them at the same time. The Integrated Raid Mirroring available for these controllers is poorly supported at
best.
The Fibre Channel controller chipset are supported by a broad variety of speeds and systems. The Apple Fibre Channel HBA is in fact the
FC949ES card.
This driver also supports target mode for Fibre Channel cards. This support may be enabled by setting the desired role of the core via the
LSI Logic firmware utility that establishes what roles the card can take on - no separate compilation is required.
SEE ALSO
cd(4), ch(4), da(4), pci(4), sa(4), scsi(4), targ(4), mptutil(8), gmultipath(8)
LSI Logic Website, http://www.lsilogic.com/.
HISTORY
The mpt driver first appeared in FreeBSD 4.6.
AUTHORS
The mpt driver was originally written for FreeBSD by Greg Ansley and marginally improved upon by Matt Jacob <mjacob@FreeBSD.org>.
Justin Gibbs <gibbs@FreeBSD.org> and Scott Long <scottl@FreeBSD.org> have made more substantial improvements.
BUGS
BSD
May 13, 2010 BSD