09-26-2002
Thk you i'll try, but for now I put a new Host name for the other eth, and it's work (it stay after reboot)
I have two eth under the same subnet and now I have problem to ping 2 switchs under the same subnet!!!!
Bye
Enzo
Quote:
Originally posted by RTM
Create a file in /etc with the following type of info:
file name
hostname.hmex where x is the interface number
hostname.qfex
hostname.lex
You have to know which interface type you have - grep them from the dmesg command
contents of file
xxx.xxx.xxx.xxx where xxx is your IP number OR
put the hostname in there but it must be /etc/hosts
Read the man pages for:
ifconfig
netmasks (section 4)
hosts (section 4)
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies
3. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
4. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
5. Solaris
I have a Quad Ethernet card in a 220R. 2 ports activated. Each has its own hostname file and both hostnames are in the hosts file. I want both ports to have the same IP address so we can use the 2nd port in case we lose communication on the port. On bootup, the box gives me:
SIOCSLIFFLAGS:... (5 Replies)
Discussion started by: hshapiro
5 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. Solaris
Hi Group,
I Have just installed quad card in my V440 machine,
I am facing problem I cn just ping its ce0 card only rest of the cards are not ping able,
here is details of my machine.
ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index
1
... (2 Replies)
Discussion started by: sameergrover
2 Replies
8. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
9. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
10. Hardware
Dear all,
I am setting up a new Ethernet network at home, I am going to have a good 100 Mbps internet connection (optic fiber) with a modem that have a gigabit ethernet card.
I would like to to measure the speed of data transmission between several servers that are going to be connected to the... (2 Replies)
Discussion started by: freddie50
2 Replies
LEARN ABOUT REDHAT
debugreiserfs
DEBUGREISERFS(8) System Manager's Manual DEBUGREISERFS(8)
NAME
debugreiserfs
SYNOPSIS
debugreiserfs [ -dDJmoqpS ] [ -j device ] [ -B blocknumber ]
device
DESCRIPTION
It helps sometimes to solve problems with reiserfs filesystems. Being called w/o options it prints super block of reiserfs filesystem found
on the device.
device is the special file corresponding to the device (e.g /dev/hdXX for IDE disk partition or /dev/sdXX for SCSI disk partition).
OPTIONS
-j device
print contents of journal. Also with the option -p it allows to pack journal into archive with other metadata
-J print journal header.
-d print formatted nodes of the internal tree of the filesystem
-D print formatted nodes of all used blocks of the filesystem
-m print contents of bitmap (not very useful)
-o print objectid map (not very useful)
-1 blocknumber
print specified block of the filesystem
-p Makes debugreiserfs to find filesystem metadata This option exists to help reiserfsck debugging. If reiserfsck fails - you may
extract filesystem metadata with debugreiserfs -p /dev/xxx |gzip -c > xxx.gz. We download that data and make the filesystem similar
to your with gunzip -c xxx.gz | unpack /dev/xxx (unpack is included into reiserfsprogs package). This usually allows to reproduce
and debug the problem quickly. When data file is not too large.
-S When -S is not specified -p deals with blocks marked used in the filesystem bitmap. With this option set they will work with whole
device.
-q Suppress showing speed of progress when -p is in use
AUTHOR
This version of debugreiserfs has been written by Hans Reiser <reiser@idiom.com>.
BUGS
There are probably few of them. Please, report bugs to ReiserFS mail-list <reiserfs-list@namesys.com>.
SEE ALSO
reiserfsck(8), mkreiserfs(8)
Reiserfsprogs 3.6.4 January 2002 DEBUGREISERFS(8)