|
|
Sponsored Content
Special Forums
IP Networking
Quad Fast Ethernet Card on Sparc 10?
Post 28928 by croccopollo on Thursday 26th of September 2002 11:26:39 AM
09-26-2002
Thk you i'll try, but for now I put a new Host name for the other eth, and it's work (it stay after reboot)
I have two eth under the same subnet and now I have problem to ping 2 switchs under the same subnet!!!!
Bye
Enzo
I have two eth under the same subnet and now I have problem to ping 2 switchs under the same subnet!!!!
Bye
Enzo
Quote:
Originally posted by RTM
Create a file in /etc with the following type of info:
file name
hostname.hmex where x is the interface number
hostname.qfex
hostname.lex
You have to know which interface type you have - grep them from the dmesg command
contents of file
xxx.xxx.xxx.xxx where xxx is your IP number OR
put the hostname in there but it must be /etc/hosts
Read the man pages for:
ifconfig
netmasks (section 4)
hosts (section 4)
Create a file in /etc with the following type of info:
file name
hostname.hmex where x is the interface number
hostname.qfex
hostname.lex
You have to know which interface type you have - grep them from the dmesg command
contents of file
xxx.xxx.xxx.xxx where xxx is your IP number OR
put the hostname in there but it must be /etc/hosts
Read the man pages for:
ifconfig
netmasks (section 4)
hosts (section 4)
|
|
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies
3. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
4. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
5. Solaris
I have a Quad Ethernet card in a 220R. 2 ports activated. Each has its own hostname file and both hostnames are in the hosts file. I want both ports to have the same IP address so we can use the 2nd port in case we lose communication on the port. On bootup, the box gives me:
SIOCSLIFFLAGS:... (5 Replies)
Discussion started by: hshapiro
5 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. Solaris
Hi Group,
I Have just installed quad card in my V440 machine,
I am facing problem I cn just ping its ce0 card only rest of the cards are not ping able,
here is details of my machine.
ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index
1
... (2 Replies)
Discussion started by: sameergrover
2 Replies
8. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
9. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
10. Hardware
Dear all,
I am setting up a new Ethernet network at home, I am going to have a good 100 Mbps internet connection (optic fiber) with a modem that have a gigabit ethernet card.
I would like to to measure the speed of data transmission between several servers that are going to be connected to the... (2 Replies)
Discussion started by: freddie50
2 Replies
LEARN ABOUT OPENSOLARIS
check-hostname
check-hostname(1M) System Administration Commands check-hostname(1M) NAME
check-hostname - check if sendmail can determine the system's fully-qualified host name SYNOPSIS
/usr/sbin/check-hostname DESCRIPTION
The check-hostname script is a migration aid for sendmail(1M). This script tries to determine the local host's fully-qualified host name (FQHN) in a manner similar to sendmail(1M). If check-hostname is able to determine the FQHN of the local host, it reports success. Other- wise, check-hostname reports how to reconfigure the system so that the FQHN can be properly determined. FILES
/etc/hosts Host name database /etc/nsswitch.conf Name service switch configuration file /etc/resolv.conf Configuration file for name server routines ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWsndmu | +-----------------------------+-----------------------------+ |Interface Stability |Evolving | +-----------------------------+-----------------------------+ SEE ALSO
domainname(1M), sendmail(1M), hosts(4), attributes(5) SunOS 5.11 8 Mar 2006 check-hostname(1M)