09-23-2002
It usually the following command:
hostname system.domain.com
Most Unix will also have a boot option which will configure tis for you at boot time!
10 More Discussions You Might Find Interesting
1. IP Networking
Hello all, I have this Intel Pentium 233/128 running Solaris 8. I also have a dhcp/router/dns running SuSElinux 7.2.(Sorry if it is out of topic here) My problem is that the Solaris box when it tries to configure the interface (elxl0) via dhcp it fails. It appears, according to the... (1 Reply)
Discussion started by: jdevarie
1 Replies
2. UNIX for Advanced & Expert Users
Hi you all. I'm trying to enable DHCP in a Sun Utra 5 runing Solaris 8 but during the boot process it sends me the message : "Device not in appropiate status"
Do anyone have enabled DHCP on solaris 8?
Any Procedure?
The DHCP server is an NT I guess. (2 Replies)
Discussion started by: alex blanco
2 Replies
3. UNIX for Dummies Questions & Answers
HI,
New to Unix and I inherited a network that runs DHCP in manual configuration mode. Basically, in order for a machine to get an IP it has to have an entry in dhcpd.conf with its MAC address mapped to a hostname (the hostname then maps to an IP address listed in the DNS db file). If there is... (2 Replies)
Discussion started by: NJay
2 Replies
4. UNIX for Advanced & Expert Users
Last question for today!! :rolleyes:
In what file does the DHCP server keep its list of leases?
THANKS!!! :)
Maria from Maria (2 Replies)
Discussion started by: marjeg
2 Replies
5. Solaris
Can someone help me with this please. I am new to this:
I am trying to install Solaris 8 over the network using my DHCP. After I type the comman:
./add_install_client -d -e 8:0:20:7e:97:51
I would get something like this:
cleaning up preexisting install client "8:0:20:7e:97:51"... (0 Replies)
Discussion started by: aliban83
0 Replies
6. IP Networking
can I request for an ipaddress through dhcp client by sending ipaddress as input during the invokation of dhcpclient so that it requests the server for the same,instead of depending on the configuration file . (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies
7. UNIX for Dummies Questions & Answers
Hi All,
I am trying to configure dhcp server on a linux host with eth0:1 which is using 192.168.1.10
I also want to restrict my DHCP client to just one Host adcnew222.
DHCP Server Host name - adcnew111
DHCP client name - adcnew222
My conf file is as follows on dhcp server :
... (2 Replies)
Discussion started by: sriram003
2 Replies
8. IP Networking
Dear Experts,
I have a TI DM8148 EVM board REV C, the EZSDK5.05 SW package, and DVRRDK1.09 SW package.
EZSDK5.05, DVRRDK1.09 both use Linux2.6.37, however, there are some modifications between these two kernels.
When I use uImage of DVRRDK1.09 to boot up EVM board, this board can be given a... (0 Replies)
Discussion started by: oobin168
0 Replies
9. IP Networking
Hi All ,
please view the set up below:
-------------------------------------------------------------------
| DHCP Server |-----------| ROUTER & |-----------| Clients |
| 192.168.99.1 | - -<eth1>| DHCP-RELAY|<eth2>-- | 192.168.88.X |
... (2 Replies)
Discussion started by: gdangoor
2 Replies
10. IP Networking
I have a DHCP thing on my HP printer. How can I find information on numbers for that? (2 Replies)
Discussion started by: teak
2 Replies
LEARN ABOUT MOJAVE
installgrub
installgrub(1M) installgrub(1M)
NAME
installgrub - install GRUB in a disk partition or a floppy
SYNOPSIS
/sbin/installgrub [-fm] stage1 stage2 raw-device
The installgrub command is an -only program. GRUB stands for GRand Unified Bootloader.
installgrub installs GRUB stage 1 and stage 2 files on the boot area of a disk partition. If you specify the -m option, installgrub
installs the stage 1 file on the master boot sector of the disk.
The installgrub command accepts the following options:
-f
Suppresses interaction when overwriting the master boot sector.
-m
Installs GRUB stage1 on the master boot sector interactively.
The installgrub command accepts the following operands:
stage1
The name of the GRUB stage 1 file.
stage2
The name of the GRUB stage 2 file.
raw-device
The name of the device onto which GRUB code is to be installed. It must be a character device that is readable and writable. For disk
devices, specify the slice where the GRUB menu file is located. (For Solaris it is the root slice.) For a floppy disk, it is
/dev/rdiskette.
Example 1: Installing GRUB on a Hard Disk Slice
The following command installs GRUB on a system where the root slice is c0d0s0:
example# /sbin/installgrub /boot/grub/stage1
/boot/grub/stage2 /dev/rdsk/c0d0s0
Example 2: Installing GRUB on a Floppy
The following command installs GRUB on a formatted floppy:
example# mount -F pcfs /dev/diskette /mnt
# mkdir -p /mnt/boot/grub
# cp /boot/grub/* /mnt/boot/grub
# umount /mnt
# cd /boot/grub
# /sbin/installgrub stage1 stage2 /dev/rdiskette
/boot/grub
Directory where GRUB files reside.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
boot(1M), fdisk(1M), fmthard(1M), kernel(1M), attributes(5)
Installing GRUB on the master boot sector (-m option) overrides any boot manager currently installed on the machine. The system will always
boot the GRUB in the Solaris partition regardless of which fdisk partition is active.
24 May 2005 installgrub(1M)