09-23-2002
It usually the following command:
hostname system.domain.com
Most Unix will also have a boot option which will configure tis for you at boot time!
10 More Discussions You Might Find Interesting
1. IP Networking
Hello all, I have this Intel Pentium 233/128 running Solaris 8. I also have a dhcp/router/dns running SuSElinux 7.2.(Sorry if it is out of topic here) My problem is that the Solaris box when it tries to configure the interface (elxl0) via dhcp it fails. It appears, according to the... (1 Reply)
Discussion started by: jdevarie
1 Replies
2. UNIX for Advanced & Expert Users
Hi you all. I'm trying to enable DHCP in a Sun Utra 5 runing Solaris 8 but during the boot process it sends me the message : "Device not in appropiate status"
Do anyone have enabled DHCP on solaris 8?
Any Procedure?
The DHCP server is an NT I guess. (2 Replies)
Discussion started by: alex blanco
2 Replies
3. UNIX for Dummies Questions & Answers
HI,
New to Unix and I inherited a network that runs DHCP in manual configuration mode. Basically, in order for a machine to get an IP it has to have an entry in dhcpd.conf with its MAC address mapped to a hostname (the hostname then maps to an IP address listed in the DNS db file). If there is... (2 Replies)
Discussion started by: NJay
2 Replies
4. UNIX for Advanced & Expert Users
Last question for today!! :rolleyes:
In what file does the DHCP server keep its list of leases?
THANKS!!! :)
Maria from Maria (2 Replies)
Discussion started by: marjeg
2 Replies
5. Solaris
Can someone help me with this please. I am new to this:
I am trying to install Solaris 8 over the network using my DHCP. After I type the comman:
./add_install_client -d -e 8:0:20:7e:97:51
I would get something like this:
cleaning up preexisting install client "8:0:20:7e:97:51"... (0 Replies)
Discussion started by: aliban83
0 Replies
6. IP Networking
can I request for an ipaddress through dhcp client by sending ipaddress as input during the invokation of dhcpclient so that it requests the server for the same,instead of depending on the configuration file . (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies
7. UNIX for Dummies Questions & Answers
Hi All,
I am trying to configure dhcp server on a linux host with eth0:1 which is using 192.168.1.10
I also want to restrict my DHCP client to just one Host adcnew222.
DHCP Server Host name - adcnew111
DHCP client name - adcnew222
My conf file is as follows on dhcp server :
... (2 Replies)
Discussion started by: sriram003
2 Replies
8. IP Networking
Dear Experts,
I have a TI DM8148 EVM board REV C, the EZSDK5.05 SW package, and DVRRDK1.09 SW package.
EZSDK5.05, DVRRDK1.09 both use Linux2.6.37, however, there are some modifications between these two kernels.
When I use uImage of DVRRDK1.09 to boot up EVM board, this board can be given a... (0 Replies)
Discussion started by: oobin168
0 Replies
9. IP Networking
Hi All ,
please view the set up below:
-------------------------------------------------------------------
| DHCP Server |-----------| ROUTER & |-----------| Clients |
| 192.168.99.1 | - -<eth1>| DHCP-RELAY|<eth2>-- | 192.168.88.X |
... (2 Replies)
Discussion started by: gdangoor
2 Replies
10. IP Networking
I have a DHCP thing on my HP printer. How can I find information on numbers for that? (2 Replies)
Discussion started by: teak
2 Replies
LEARN ABOUT CENTOS
plymouth
PLYMOUTH(8) System Administration PLYMOUTH(8)
NAME
plymouth - A graphical boot system and logger
DESCRIPTION
plymouth is a graphical boot system for Linux which takes advantage of the kernel-based mode setting (KMS) available for modern graphic
cards to provide a seamless, flickerfree and attractive boot screen. It allows to choose between various, static or animated graphical
themes to spruce up the startup and avoid the noise generated by the vast amount of kernel messages while the machine boots into X. On
systems where kernel-based mode setting is not available, plymouth falls back to a text mode boot screen which provides a simple progress
bar to pro- vide feedback during boot.
In order for the configured default plymouth theme to be loaded during boot, the option `splash' (or `rhgb' for backward compatibility with
the RHGB boot splash) must be provided at the kernel command line. Without this command line option, plymouth will default to showing
detailed boot output.
During the boot process, the user can switch between the graphical theme and the detailed boot output using the Escape key.
SEE ALSO
grub(8), plymouth-set-theme(1), plymouthd(8), plymouth(1), http://www.freedesktop.org/wiki/Software/Plymouth
AUTHORS
plymouth was originally prototyped and named by Kristian Hogsberg, originally written by Ray Strode and has had significant contributions
from Charlie Brej. It has also had contributions from Peter Jones, Adam Jackson, Frederic Crozat and others.
plymouth PLYMOUTH(8)