09-20-2002
Use this command:
$ ifconfig -a
Your output will be like this:
lo0: flags=849<UP,LOOPBACK,RUNNING,MULTICAST> mtu 8232
inet 127.0.0.1 netmask ff000000
hme0: flags=863<UP,BROADCAST,NOTRAILERS,RUNNING,MULTICAST> mtu 1500
inet 10.14.1.20 netmask fffffc00 broadcast 10.14.1.255
You will have either a le0, hme0, qfe0...the inet is the IP address.
Check the man page on ifconfig
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi all,
what is the comamnd to get the server address using the IP address ?
Please help.
Thanks,
Sona. (3 Replies)
Discussion started by: Sona
3 Replies
2. Shell Programming and Scripting
Hi,
I want to know the IP of my Unix server in my script programming.
Below are the my trial and i didn't find anything useful for me.because i want only IP.
hostname -> Giving the name of the server and
hostanme -i -> Giving the error message that..i am not super user.
ipConfig ->... (7 Replies)
Discussion started by: Balamani
7 Replies
3. AIX
How to find the router IP address (2 Replies)
Discussion started by: AIXlearner
2 Replies
4. IP Networking
Hello,
I have a server in C that is listening on a socket using s_addr = INADDR_ANY, and clients connect to it. How can I know which address did the client use to connect to that socket?
It might be 127.0.0.1 (if the server is running locally), 192.168.x.x (if the client is from inside the... (1 Reply)
Discussion started by: royger
1 Replies
5. HP-UX
I am moving an HP UX 9000 server to a new subnet. How do I change the server's IP address??
Many thanks in advance
:confused: (3 Replies)
Discussion started by: ldaliosmane
3 Replies
6. Red Hat
Where can you find your DHCP Server address? I checked all of the files that this mentioned with no luck.
Quick HOWTO : Ch08 : Configuring the DHCP Server - Linux Home Networking (6 Replies)
Discussion started by: cokedude
6 Replies
7. Programming
Hello,
I developed a client task in C and a server task in C (an application strongly coupled). The client needs the server IP address to connect to the server. The problem is: I don't know in advance which machine will run the client and which machine will run the server so I can know the ip... (3 Replies)
Discussion started by: chercheur857
3 Replies
8. UNIX for Dummies Questions & Answers
Hi Guys,
I want to find another(Local host) machine IP address from my machine.. We are all connected in the same server, I mean same LAN.
What i done is
Connected with that user machine using SSH and SU.. After that i used IFCONFIG but it shows my Ip address. Can not able to get the... (8 Replies)
Discussion started by: Adhi
8 Replies
9. Red Hat
Hi,
How to find ip address of Linux servers ?
I know by ping command we can find ip address but wanted to check with you.
Thanks,
Maddy (5 Replies)
Discussion started by: Maddy123
5 Replies
10. Red Hat
I want to find out the DHCPv6 server's ip address in the network. I went through the lease files but could find only duid/server-id and not the IPv6 address of the dhcp server. And I couldn't find any commands to get that information. Is there a way to get the DHCPv6 server's IPv6 address?
... (0 Replies)
Discussion started by: bshalini
0 Replies
NTB(4) BSD Kernel Interfaces Manual NTB(4)
NAME
ntb, ntb_hw, if_ntb -- Intel(R) Non-Transparent Bridge driver
SYNOPSIS
To compile this driver into your kernel, place the following lines in your kernel configuration file:
device ntb_hw
device if_ntb
Or, to load the driver as a module at boot, place the following line in loader.conf(5):
if_ntb_load="YES"
DESCRIPTION
The ntb driver provides support for the Non-Transparent Bridge (NTB) in the Intel S1200, Xeon E3 and Xeon E5 processor families.
The NTB allows you to connect two computer systems using a PCI-e link if they have the correct equipment and connectors.
CONFIGURATION
The NTB memory windows need to be configured by the BIOS. If your BIOS allows you to set their size, you should set the size of both memory
windows to 1 MiB. This needs to be done on both systems.
Each system needs to have a different IP address assigned. The MAC address is randomly generated. Also for maximum performance, the MTU
should be set to 16 kiB. This can be done by adding the line below to rc.conf(5):
ifconfig_ntb0="inet 192.168.1.10 netmask 255.255.255.0 mtu 16384"
And on the second system :
ifconfig_ntb0="inet 192.168.1.11 netmask 255.255.255.0 mtu 16384"
If you are using the UDP protocol, you may want to increase the net.inet.udp.maxdgram sysctl(8) variable.
SEE ALSO
rc.conf(5), sysctl(8)
AUTHORS
The ntb driver was developed by Intel and originally written by Carl Delsey <carl@FreeBSD.org>.
BUGS
If the driver is unloaded, it cannot be reloaded without a system reboot.
The network support is limited. It isn't fully configurable yet. It also isn't integrated into netgraph(4) or bpf(4).
NTB to Root Port mode is not yet supported.
There is no way to protect your system from malicious behavior on the other system once the link is brought up. Anyone with root or kernel
access on the other system can read or write to any location on your system. In other words, only connect two systems that completely trust
each other.
BSD
Apr 11, 2013 BSD