09-18-2002
Is youe eth0 built into the kernel or as a module? If its a module type lsmod and see if it is running. If its not there try to modprobe it and see waht happens.
10 More Discussions You Might Find Interesting
1. IP Networking
Hi there guys!
I have a small task that I have to accomplish, but I don't seem to be able to do that.
I have a server that I don't have physical access to, and I mostly control it with webmin. The server is running 2 websites. Both of these websites have their own domains that are linked to... (1 Reply)
Discussion started by: D-Lexy
1 Replies
2. Red Hat
when i finish installed rhel 4.4 to my hp dl585 box, ifcfg-eth0 and ifcfg-eth1 is not available.when i ifconfig -a,i can not see the eth0 and eth1, only lo0 and si0. Unlike to the other server i found eth0 and eth1 files in
/etc/sysconfig/network-scripts/.
what will i do? (2 Replies)
Discussion started by: kenshinhimura
2 Replies
3. Ubuntu
Greetings,
I have installed a Ubuntu server and attempting put a static IP address on interface ETH0. I edited the /etc/network/interfaces with the following:
auto eth0
iface eth0 inet static
address 192.168.203.270
gateway 192.168.203.1
netwask 255.255.255.0
network 192.168.0.0... (2 Replies)
Discussion started by: jroberson
2 Replies
4. UNIX for Dummies Questions & Answers
Hi,
Just installed Centos 5.1 on HP DL360, on this system I have to close to ten nic's. How can I find which one is eth0? When I do " ifconfig -a" I see all of them, but I can't tell which is eth0?
Please advice. (2 Replies)
Discussion started by: samnyc
2 Replies
5. UNIX for Dummies Questions & Answers
Hi Guys,
is there a way to send traffic coming from the source iface (eth0, eth1)? i need to test traffic that will come from both eth0 and eth1 from a Linux box.
Thanks,
Martin (0 Replies)
Discussion started by: mdap
0 Replies
6. Red Hat
Hi,
I have just installed RHEL 5.4 on a BL430c-class server and I am attempting to connect to the network only when I try and start eth0, I get the following error?
"Bringing up Interface eth0: hp device eth0 does not seem to be present, delaying initialization."
I am using a HP... (18 Replies)
Discussion started by: Duffs22
18 Replies
7. Red Hat
Hi,
I have noticed some performance issues on my RHEL5 server but the memory and CPU utilization on the box is fine.
I have a 1G full duplexed eth0 card and I am suspicious that this may be causing the problem. My eth0 settings are as follows:
Settings for eth0:
Supported ports: ... (12 Replies)
Discussion started by: Duffs22
12 Replies
8. Red Hat
Hello, I'm using dell inspiron 14R laptop and I installed Redhat enterprise 6.2 on this. After successfully installation i did not found any network interface on this.
when i'm trying to load/add qeth driver . The driver is not found showing this message.
Bash: lsmod | grep qeth
Bash:... (4 Replies)
Discussion started by: dearsumon
4 Replies
9. IP Networking
Hi all,
I am running a CentOS 6.4 box as an IDS and I need to configure one interface as the management interface which will require a firewall. However other ports (in promisc mode without IP) will have to be configured such that IPtables allows all traffic.
I need to achieve this by editing... (4 Replies)
Discussion started by: landossa
4 Replies
10. Red Hat
Hi guys,
I really need your help with this.
My network interface eth0 is up but not running. I checked udev rules and ifcfg-eth0 files to make sure the mac address are the same.
It just would not come up. Please please I will really appreciate the help here.
Thank you in advance. (3 Replies)
Discussion started by: cjashu
3 Replies
RMMOD(8) RMMOD(8)
NAME
rmmod - simple program to remove a module from the Linux Kernel
SYNOPSIS
rmmod [ -f ] [ -w ] [ -s ] [ -v ] [ modulename ]
DESCRIPTION
rmmod is a trivial program to remove a module (when module unloading support is provided) from the kernel. Most users will want to use
modprobe(8) with the -r option instead.
OPTIONS
-v --verbose
Print messages about what the program is doing. Usually rmmod prints messages only if something goes wrong.
-f --force
This option can be extremely dangerous: it has no effect unless CONFIG_MODULE_FORCE_UNLOAD was set when the kernel was compiled.
With this option, you can remove modules which are being used, or which are not designed to be removed, or have been marked as
unsafe (see lsmod(8)).
-w --wait
Normally, rmmod will refuse to unload modules which are in use. With this option, rmmod will isolate the module, and wait until the
module is no longer used. Nothing new will be able to use the module, but it's up to you to make sure the current users eventually
finish with it. See lsmod(8)) for information on usage counts.
-s --syslog
Send errors to syslog instead of standard error.
-V --version
Show version of program and exit.
COPYRIGHT
This manual page originally Copyright 2002, Rusty Russell, IBM Corporation. Maintained by Jon Masters and others.
SEE ALSO
modprobe(8), insmod(8), lsmod(8) modinfo(8)
2010-03-01 RMMOD(8)