Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Hi all,
Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- --... (0 Replies)
Hello,
I have just installed Solaris 9 x86 in a VMWare and the 1st problem I have is to enable the networking. I can only see the loopback interface and nothing else.
- I dont have any /etc/hostnames.xxx
- ifconfig -a shows only the loopback
- kstat -c net shows only the loopback ...
Any... (11 Replies)
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT LINUX
rgephy
RGEPHY(4) BSD Kernel Interfaces Manual RGEPHY(4)NAME
rgephy -- RealTek RTL8168/8169/8110/8211 series 10/100/1000 Gigabit Ethernet PHY driver
SYNOPSIS
To compile all available PHY drivers into the kernel, place the following line in your kernel configuration file:
device miibus
Alternatively, to selectively compile this driver into the kernel, place the following lines in your kernel configuration file instead:
device mii
device rgephy
DESCRIPTION
The rgephy driver supports the RealTek RTL8168, RTL8169, RTL8110 and RTL8211 series integrated 10/100/1000 Gigabit Ethernet PHYs.
In order to get a list of media types and options supported by a specific instance of the rgephy driver, run ifconfig -m on the instance of
its parent MAC driver.
Additionally, the rgephy driver supports the following special media option:
flag0 When manually setting media type and options via ifconfig(8), the rgephy driver by default also triggers an autonegotiation advertis-
ing the selected media. This is done in order to work around hardware issues in certain scenarios. It is believed that this behavior
does not cause harm in general but in fact can have an adverse effect in edge cases. In order to manually set the media type and
options without also triggering an autonegotiation, the rgephy driver allows to turn this behavior off via the flag0 media option.
Note that this special media option will not show up in the output of ifconfig(8), even when set.
EXAMPLES
Manually set 100BASE-TX full-duplex without also triggering an autonegotiation:
ifconfig re0 media 100baseTX mediaopt full-duplex,flag0
SEE ALSO intro(4), miibus(4), ifconfig(8)BSD January 16, 2011 BSD