06-06-2001
What flavour of UNIX are you running?
10 More Discussions You Might Find Interesting
1. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
2. Solaris
Hi all,
Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- --... (0 Replies)
Discussion started by: baraghun
0 Replies
3. Solaris
Hello,
I have just installed Solaris 9 x86 in a VMWare and the 1st problem I have is to enable the networking. I can only see the loopback interface and nothing else.
- I dont have any /etc/hostnames.xxx
- ifconfig -a shows only the loopback
- kstat -c net shows only the loopback ...
Any... (11 Replies)
Discussion started by: Tex-Twil
11 Replies
4. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
7. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT HPUX
standards
standards(5) File Formats Manual standards(5)
NAME
standards - UNIX standards behavior on HP-UX
DESCRIPTION
HP-UX conforms to various UNIX standards. In some cases, these standards conflict. This manpage describes the methods that programmers
and users must follow to have an application conform and execute according to a particular UNIX standard.
UNIX Standard Conformant Programmer Environment
The following table lists feature test macros and environment variables that must be defined while compiling an application. Both a fea-
ture test macro and an environment variable must be defined while compiling the application so that the application conforms and executes
according to a particular UNIX standard. Otherwise, the behavior is undefined.
Standard Feature Test Macros to be Environment variable
defined during compilation to be set
UNIX 95 _XOPEN_SOURCE_EXTENDED=1 UNIX95 or
UNIX_STD=95 or
UNIX_STD=1995
UNIX 2003 _XOPEN_SOURCE=600 UNIX_STD=2003
The compiler uses the feature test macros to obtain the appropriate namespace from the header files. The compiler uses the environment
variable to link in an appropriate object file to the executable. Using the environment variable customizes libc to match UNIX standards
for various functions.
If an application has already been compiled for default HP-UX behavior or for one particular standard, and needs to change to a particular
UNIX standard behavior, recompile the application as specified in the above table.
For an HP-UX command to conform to a particular UNIX standard behavior, the application has to set the corresponding environment variable
as specified in the above table before executing that command.
UNIX Standard Conformant User Environment
To enable a particular UNIX standard conformant user environment, set the corresponding environment variable as defined in the above table.
EXAMPLES
The following examples shows an application example. To have the system be conformant to UNIX2003 behavior, set the environment variable
to and define the feature test macro before compilation.
The following example changes the command to have UNIX95 behavior by setting one of the environment variables to or to before executing
that command. There are three ways of setting the environment variable for UNIX95:
or
or
SEE ALSO
cc(1), stdsyms(5).
standards(5)