09-09-2002
You can also check out Ethereal and it's command line driven counterpart, Tethereal. I have had a good experience with it in the past.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
is there a snoop equivalent in other flavors of unix? HPUX, SCO or linux.
TIA
Peter (2 Replies)
Discussion started by: pbonilla
2 Replies
2. UNIX for Advanced & Expert Users
is there a snoop equivalent in other flavors of unix? for AIX IBM (1 Reply)
Discussion started by: jcasares
1 Replies
3. Solaris
Hello! It is my first post in this forum :).
I`m facing a strange issue. I am using a Solaris 8 as OS, and using the ipnat (ipf) to NAT an incoming port to another, as following:
Host SUN with Solaris 8/NAT WEB Page
(A.B.C.D:80) ---> |A.B.C.D:80 ->... (0 Replies)
Discussion started by: mf_lattanzi
0 Replies
4. HP-UX
Error received when I tried to restore a blank disk with an 'auto recovery' DDS tape via HP-UX recovery system 2.0 onto a 1Gb SCSI. I assumed it would do the setup, wrong. Could someone tell me the procedure to initial disk for recovering files using cpio. The system is a HP-UX 9.04 version on a... (1 Reply)
Discussion started by: admin wanabee
1 Replies
5. Solaris
Hi.
I'm trying to capture traffic with the snoop command using the net expression but I fail when a I've to specify a subnet
ex: 10.201.64/18
Did you know the correct syntax?
I've tried with
snoop -ta -x0 net 10.201.64.0 255.255.192.0
but doesn't match.
Thnx (4 Replies)
Discussion started by: kurtolo
4 Replies
6. Shell Programming and Scripting
Hi,
I want to write a script that checks an interface with the snoop command, if there is no traffic in 10 minutes on port 123 from the ip add 10.*.*.* it should send a e-mail.but i don't know how to start writing this script does anybody have an idea or an sample script that i can modifi.
... (2 Replies)
Discussion started by: tafil
2 Replies
7. Solaris
Is there anywhere we can get details about what we should expect to see and not to see in some packets captured with "snoop" during troubleshooting a problem? I know we can capture packes for a failed transaction and compare them with packets for a successful trasaction.Is that the only way to... (4 Replies)
Discussion started by: Pouchie1
4 Replies
8. UNIX for Advanced & Expert Users
I was trying to install the solaris snoop package on a flavor of linux. I got the tar file, unzipped it. when I CD to the unzipped snoop directory, I ran the command ./configure ; make and I got the following error. Did anybody run into this before? what can I do to install snoop?
checking... (1 Reply)
Discussion started by: Pouchie1
1 Replies
9. UNIX for Advanced & Expert Users
Hi,
Can anyone please tell me a ftp site where I can download the solaris snoop package? I need to download the package so I can use the command in a Linux environment instead of using tcpdump. Need practice with snoop.
Thanks for your help. (3 Replies)
Discussion started by: Pouchie1
3 Replies
10. Shell Programming and Scripting
Hi
#Testing for file existence
if ; then
echo 'SCHOOL data is available for processing'
else
echo 'SCHOOL DATA IS NOT AVAILABLE FOR PROCESSING'
:
i wrote a script, where it begins by checking if file exists or not.
If it exists, it truncates the database... (2 Replies)
Discussion started by: rxg
2 Replies
LEARN ABOUT DEBIAN
svn-bisect
SVN-BISECT(1) General Commands Manual SVN-BISECT(1)
NAME
svn-bisect - Bisect Subversion revisions to find a regression
SYNOPSIS
svn-bisect start [good_rev [bad_rev]]
svn-bisect {good|bad} [rev]
svn-bisect run command
svn-bisect reset
svn-bisect status
DESCRIPTION
svn-bisect helps to automate finding a bug or behavior change in a Subversion working copy. Given an initial "good" revision, with the
desired or original behavior, and a newer "bad" revision, with the undesired or modified behavior, svn-bisect will do a binary search
through the revision range to find which revision caused the change.
svn-bisect must be initialized in a working copy, with svn-bisect start. It also needs to be given at least one good revision (the base-
line) and one bad revision (known modified behavior) revision.
Sub-commands:
start Initializes or reinitializes svn-bisect; optionally takes good and bad revision parameters.
good rev
bad rev
Tells svn-bisect that a revision is good or bad, defining or narrowing the search space. If not specified, revision defaults to the
current revision in the working copy. svn-bisect will then update to a revision halfway between the new good and bad boundaries.
If this update crosses a point where a branch was created, it switches in or out of the branch.
reset Resets the working copy to the revision and branch where svn-bisect start was run. In the simple case this is equivalent to rm -r
.svn-bisect; svn update, but not if it has crossed branches, and not if you did not start at the HEAD revision. In any case,
svn-bisect never keeps track of mixed-revision working copies, so do not use svn-bisect in a working copy that will need to be
restored to mixed revisions.
status Prints a brief status message.
run command
Runs the bisection in a loop. You must have already defined initial good and bad boundary conditions. Each iteration through the
loop runs command as a shell command (a single argument, quoted if necessary) on the chosen revision, then marks the revision as
good or bad, based on the exit status of command.
EXAMPLES
Assume you are trying to find which revision between 1250 and 1400 caused the make check command to fail.
svn-bisect start 1250 1400
svn-bisect run 'make check'
svn-bisect reset
ENVIRONMENT
SVN The Subversion command-line program to call (default svn).
FILES
.svn-bisect
The directory containing state information, removed after a successful bisection.
SEE ALSO
git-bisect(1).
AUTHOR
Written by Robert Millan and Peter Samuelson, for the Debian Project (but may be used by others).
2009-10-22 SVN-BISECT(1)