09-06-2002
gateway
I used "route" to add the default gateway
I wrote this:
route add default 19x.x.x.x 0
but this is not permanent default gateway.
Do I need to use another command?
Thank a lot
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
How can I change the gateway address on my sco Openserver 5.0.6. A cisco firewall is recently installed but the gateway on the system is still pointing at the old one.
I want it to use the gateway address of the router.
Please help. Thanks (2 Replies)
Discussion started by: sshokunbi
2 Replies
2. Red Hat
Hi,
in which file and how shuold be decalred a gateway and its IP adresse ?
Where and how add a gateway ?
Many thanks before. (3 Replies)
Discussion started by: big123456
3 Replies
3. Programming
how we can get the gateway address.
i know gethostname used for ipaddress
how we can get the system gateway address.
thank u inadvance,
sree (2 Replies)
Discussion started by: phani_sree
2 Replies
4. SCO
Hy everybody !
I'm new on your forum, i'm french and don't speak a good english, so scuse me please for it !
I would to know how modify a gateway on a SCO 5.06
We have a problem, we have multi "beach" adress, one is 192.1.1.x, an other is 192.1.4.x
Actually, the computer on 192.1.4.x... (2 Replies)
Discussion started by: LB59
2 Replies
5. AIX
Dear folks,
How can delete the gateway from smitty or by command, Because I have 2 gatway in the system and I tried to delete by smitty it gave me failed command (7 Replies)
Discussion started by: magasem
7 Replies
6. AIX
Hi,
I have two interfaces on m AIX 5.3 box. One going to 192.168.1.x and it has a gateway of 192.168.1.1.
I configured the other gateway with 192.168.2.x and the default gateway as 192.168.2.1. But I can't get connectivity to the 192.168.2.1 network. Can someone help me out and let me know... (7 Replies)
Discussion started by: bbbngowc
7 Replies
7. Solaris
Hi all,
Just now i had change the gateway for a server
Go to /etc/defaultrouter, change to 10.86.33.1
route delete default 10.86.39.222
route add default 10.86.33.1
now cannot telnet to the server already..
any idea? (5 Replies)
Discussion started by: SmartAntz
5 Replies
8. AIX
Hello,
I am new to Unix :D and have been trying to configure an AIX server running 5.3. I used smitty or smit to configure interface 0 on the server. I am able to ping the IP I set, however I am still unable to ping the gateway. I configured the IP by navigating to Communications Applications... (6 Replies)
Discussion started by: cdub50
6 Replies
9. Linux
Dear Sir
I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper.
I am having a problem, configuring static call routing on GNUGK
in the section
... (0 Replies)
Discussion started by: mfondoum
0 Replies
10. UNIX for Beginners Questions & Answers
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT FREEBSD
traceroute6
TRACEROUTE6(8) BSD System Manager's Manual TRACEROUTE6(8)
NAME
traceroute6 -- print the route IPv6 packets will take to a network node
SYNOPSIS
traceroute6 [-adIlnNrvU] [-f firsthop] [-g gateway] [-m hoplimit] [-p port] [-q probes] [-s src] [-w waittime] [-A as_server] target
[datalen]
DESCRIPTION
The traceroute6 utility uses the IPv6 protocol hop limit field to elicit an ICMPv6 TIME_EXCEEDED response from each gateway along the path to
some host.
The only mandatory parameter is the destination host name or IPv6 address. The default probe datagram carries 12 bytes of payload, in addi-
tion to the IPv6 header. The size of the payload can be specified by giving a length (in bytes) after the destination host name.
Other options are:
-a Turn on AS# lookups for each hop encountered.
-A as_server
Turn on AS# lookups and use the given server instead of the default.
-d Debug mode.
-f firsthop
Specify how many hops to skip in trace.
-g gateway
Specify intermediate gateway (traceroute6 uses routing header).
-I Use ICMP6 ECHO instead of UDP datagrams.
-l Print both host hostnames and numeric addresses. Normally traceroute6 prints only hostnames if -n is not specified, and only numeric
addresses if -n is specified.
-m hoplimit
Specify maximum hoplimit, up to 255. The default is 30 hops.
-n Do not resolve numeric address to hostname.
-N Use a packet with no upper layer header for the probes, instead of UDP datagrams.
-p port
Set UDP port number to port.
-q probes
Set the number of probe per hop count to probes.
-r Bypass the normal routing tables and send directly to a host on an attached network. If the host is not on a directly-connected net-
work, an error is returned. This option corresponds to the SO_DONTROUTE socket option; it can be used to ping a local host through
an interface that has no route through it (e.g., after the interface was dropped by a routing daemon).
-s src Src specifies the source IPv6 address to be used.
-U Use UDP datagrams for the probes. This is the default.
-v Be verbose.
-w waittime
Specify the delay time between probes.
This program prints the route to the given destination and the round-trip time to each gateway, in the same manner as traceroute.
Here is a list of possible annotations after the round-trip time for each gateway:
!N Destination Unreachable - No Route to Host.
!P Destination Unreachable - Administratively Prohibited.
!S Destination Unreachable - Not a Neighbour.
!A Destination Unreachable - Address Unreachable.
! This is printed if the hop limit is <= 1 on a port unreachable message. This means that the packet got to the destination, but
that the reply had a hop limit that was just large enough to allow it to get back to the source of the traceroute6. This was
more interesting in the IPv4 case, where some IP stack bugs could be identified by this behaviour.
EXIT STATUS
The traceroute6 utility will exit with 0 on success, and non-zero on errors.
SEE ALSO
ping(8), ping6(8), traceroute(8)
HISTORY
The traceroute6 utility first appeared in WIDE hydrangea IPv6 protocol stack kit.
BSD
August 24, 2009 BSD