Sponsored Content
Special Forums IP Networking Solaris 9 Ethernet Card Problems Post 27266 by RTM on Thursday 29th of August 2002 09:44:03 AM
Old 08-29-2002
Create a file for hme0:

echo "xxx.xxx.xxx.xxx" > /etc/hostname.hme0
(replace the xxx.xxx.xxx.xxx with your IP address)

Then insure you have the /etc/defaultrouter set up - you should be able to get this info from your Network folks if you don't know. It could be as simple as this: If your IP is 10.140.16.20 then your default router may be 10.140.16.1 or 10.140.16.254. It matters on how your network is set up.

Insure your netmask is in /etc/netmasks. Again, get with your network folks for the info.

I believe that's it.
 

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies

2. IP Networking

RedHat and Ethernet card no like each other

I have searched this forum for solution and have drawn a blank... so I come to you for help :) I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies

3. UNIX for Dummies Questions & Answers

Ethernet card problem...

I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies

4. SCO

Issue with a ethernet card

Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message: Fsstat:/dev/boot mounted Mounted /stand filesystem System auditing is not enabled. Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0) Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies

5. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies

6. Solaris

Ethernet card drivers issue...

I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do? Thanks in advance (2 Replies)
Discussion started by: younus_syed
2 Replies

7. AIX

Utilization of Ethernet Card

Hi, is it possible to find out network utilization of etherenet card in %? Regards, Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies

8. Linux

Offload parameters for Ethernet Card

Hi, Actually i want to see Offload parameter for my Eth card. Then after i try using this command Anybody can explain ? Is there any problem with my eth card ? (1 Reply)
Discussion started by: justbow
1 Replies

9. Solaris

solaris ethernet card and mounting usb drives

I had installed soalris 10 on my dell vostro 1400.It had installed succefully. If i type ifconfig -a it is showing only my loop back adpater. So how to tell me how to mount my usb drive and how to configure my lan ethernet card,My lan ethernet card is Broadcom. Tell me step... (1 Reply)
Discussion started by: testerindia25
1 Replies

10. Solaris

Problem with my Ethernet Card

Hi Gurus of Solaris. I have a problem yesterday when I was installing solaris in a x86 equipement I attached some log that I capture when I try to resolve the problem Any guru that can help please. Any command or procedure that I can run, please advice me Regards Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
face(1)                                                            User Commands                                                           face(1)

NAME
face - executable for the Framed Access Command Environment Interface SYNOPSIS
face [-i init_file] [-c command_file] [-a alias_file] [filename...] DESCRIPTION
The Framed Access Command Environment Interface (FACE) presents your files and file folders on the screen through a system of menus and forms if you are properly set up as a FACE user. filename must follow the naming convention Menu.xxx for a menu, Form.xxx for a form, and Text.xxx for a text file, where xxx is any string that conforms to the UNIX system file naming conventions. The Form and Menu Language Interpreter (FMLI) descriptor lifetime will be ignored for all frames opened by argument to face. These frames have a lifetime of immortal by default. If filename is not specified on the command line, the FACE Menu will be opened along with those objects specified by the LOGINWIN environment variables. These variables are found in the user's .environ file. OPTIONS
The following options are supported: -a alias_file Alias file -c command_file Command file -i init_file Initial file OPERANDS
The following operand is supported: filename The full pathname of the file describing the object to be opened initially. EXIT STATUS
The face command will return a non-zero exit value if the user is not properly set up as a FACE user. FILES
$HOME/pref/.environ ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWfac | +-----------------------------+-----------------------------+ SEE ALSO
env(1), attributes(5) SunOS 5.10 5 Jul 1990 face(1)
All times are GMT -4. The time now is 10:30 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy