08-29-2002
Solaris 9 Ethernet Card Problems
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS.
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies
3. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
4. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
5. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
6. Solaris
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Discussion started by: younus_syed
2 Replies
7. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
8. Linux
Hi,
Actually i want to see Offload parameter for my Eth card.
Then after i try using this command
Anybody can explain ?
Is there any problem with my eth card ? (1 Reply)
Discussion started by: justbow
1 Replies
9. Solaris
I had installed soalris 10 on my dell vostro 1400.It had installed succefully.
If i type ifconfig -a it is showing only my loop back adpater.
So how to tell me how to mount my usb drive and how to configure
my lan ethernet card,My lan ethernet card is Broadcom.
Tell me step... (1 Reply)
Discussion started by: testerindia25
1 Replies
10. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
LEARN ABOUT DEBIAN
br2684ctl
br2684ctl(8) System Manager's Manual br2684ctl(8)
NAME
br2684ctl - RFC1483/2684 Bridge Daemon
SYNOPSIS
br2684ctl [ -b ] [[ -c n ] [ -e 0|1 ] [ -p 0|1 ] [ -s sndbuf ] [ -a [itf].vpi.vci ]] ...
PARAMETERS
-a [itf].vpi.vci
ATM PVC number, VPI and VCI. (Required)
-b Puts the process in the background.
-c n br2684 interface number such as 0, 1, ... (Required)
-e 0|1 Encapsulation method: 0=LLC, 1=VC mux (the default is 0 or LLC)
-p 0|1 Payload method: 0=Routed, 1=Bridged (the default is 1 or Bridged)
-s sndbuf Send buffer size. Default is 8192.
DESCRIPTION
br2684ctl handles RFC1483/2684 bridged PDUs. This is most often used in ADSL scenarios where usually the subscribers' ethernet traffic is
encapsulated in ATM AAL5 (by bridging ADSL modems) according to RFC2684. The subscriber-side ADSL modem can be external with an ethernet
connector or an internal ADSL card in a PC. RFC1483 has been obsoleted by RFC2684.
For example it is possible to set up your Linux box to handle several ATM PVC's with bridged-1483 (sometimes referred as SNAP) encapsula-
tion. The Linux network stack might provide DHCP, IP masquerading, IP firewall services or bridge the Ethernet frames just like it had
several ethernet interfaces. In fact it can have several (logical) ethernet interfaces, where ATM is just used as a carrier.
USAGE
br2684ctl creates a new network interface named nas[n] which is bound to an specific ATM PVC. It requires two mandatory arguments: -c, the
interface number, and -a, the ATM PVC. It should be noted that the order of the command arguments matter; -c should be followed by -a. You
can create as many interfaces as necessary in one go, just make a long command line ;)
For example, following command will create a nas0 interface which uses the ATM PVC with VPI=0 and VCI=401. You need to configure the PVC
connection 0.401 on the ATM switch manually.
% br2684ctl -c 0 -a 0.401
The command will only create a new interface nas0. Next step is to assign an IP address and netmask to the interface nas0 using the ifcon-
fig command. Using ifconfig, you can also assign a Ethernet MAC address to the interface nas0, if necessary.
% ifconfig nas0 192.168.2.1 netmask 255.255.255.0
Messages are logged to the LOCAL2 syslog facility.
FILES
/var/run/br2684ctl-<iface>.pid
NOTES
This man page is based on a tutorial by by Joonbum Byun <jbyun@megaxess.com>
SEE ALSO
qos(7)
7 Jul 2003 br2684ctl(8)