08-29-2002
Solaris 9 Ethernet Card Problems
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS.
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies
3. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
4. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
5. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
6. Solaris
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Discussion started by: younus_syed
2 Replies
7. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
8. Linux
Hi,
Actually i want to see Offload parameter for my Eth card.
Then after i try using this command
Anybody can explain ?
Is there any problem with my eth card ? (1 Reply)
Discussion started by: justbow
1 Replies
9. Solaris
I had installed soalris 10 on my dell vostro 1400.It had installed succefully.
If i type ifconfig -a it is showing only my loop back adpater.
So how to tell me how to mount my usb drive and how to configure
my lan ethernet card,My lan ethernet card is Broadcom.
Tell me step... (1 Reply)
Discussion started by: testerindia25
1 Replies
10. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
LEARN ABOUT NETBSD
pcap_compile
PCAP_COMPILE(3) Library Functions Manual PCAP_COMPILE(3)
NAME
pcap_compile - compile a filter expression
SYNOPSIS
#include <pcap/pcap.h>
int pcap_compile(pcap_t *p, struct bpf_program *fp,
const char *str, int optimize, bpf_u_int32 netmask);
DESCRIPTION
pcap_compile() is used to compile the string str into a filter program. See pcap-filter(7) for the syntax of that string. program is a
pointer to a bpf_program struct and is filled in by pcap_compile(). optimize controls whether optimization on the resulting code is per-
formed. netmask specifies the IPv4 netmask of the network on which packets are being captured; it is used only when checking for IPv4
broadcast addresses in the filter program. If the netmask of the network on which packets are being captured isn't known to the program,
or if packets are being captured on the Linux "any" pseudo-interface that can capture on more than one network, a value of PCAP_NET-
MASK_UNKNOWN can be supplied; tests for IPv4 broadcast addreses will fail to compile, but all other tests in the filter program will be OK.
RETURN VALUE
pcap_compile() returns 0 on success and -1 on failure. If -1 is returned, pcap_geterr() or pcap_perror() may be called with p as an argu-
ment to fetch or display the error text.
SEE ALSO
pcap(3), pcap_setfilter(3), pcap_freecode(3), pcap_geterr(3), pcap-filter(7)
5 April 2008 PCAP_COMPILE(3)