07-12-2002
if your router is a linux box, then you can change the file
/etc/init.d/network-scripts/ifcfg-ethx
where x is the interface number.
inside that file you can specify.
DHCP=no
ON BOOT = yes
IP_ADDR = "xxx.xxx.xxx.xxx" etc.
hope this helps.
- Sirius.
10 More Discussions You Might Find Interesting
1. HP-UX
***Newbie alert***
What's the easiest way to accomplish this? An admin left our company and I have taken over his HP Workstation and moved it to a different location that is on a different IP segment.
I have performed a number of google searches but the steps I have followed haven't worked.
... (1 Reply)
Discussion started by: Steelysteel
1 Replies
2. IP Networking
I have a USB Wireless Adapter using the rum0 driver. All I want to do is set a perminent static IP for the onboard wired interface elxl0. I can plumb the wired interface up fine on the fly, but when I try to save the static IP over a reboot, I lose the IP address assigned to rum0 from my wireless... (1 Reply)
Discussion started by: ts97783
1 Replies
3. IP Networking
I am trying to write a set of scripts for my Ubuntu 810 Server to allow a user to change from DHCP to a user-supplied Static IP, Subnet, Gateway and DNS Servers.
So far I have the following, where $USERCHOICE is a user-entered value in each case:
ifconfig eth0 down && ifconfig eth0 $USERCHOICE... (1 Reply)
Discussion started by: cleanden
1 Replies
4. Solaris
Hello friend, I am new in UNIX, but I want to learn a lot
Well I have a problem to try to configure my PC with a static IP Address
(IP 192.168.1.39, Mask 255.255.255.0, gateway 192.168.1.1)
(DNS 200.48.225.130 and 200.48.225.146).
where are the file that I must be change?
The SO is Sun Solaris... (15 Replies)
Discussion started by: andresguillen
15 Replies
5. Red Hat
Hi,
I am using RHEL 5.1 and i would like to know,
how to find the whether my system is using DHCP or STATIC IP
with out looking at /etc/sysconfig/network-scripts/ifconfig-eth0 configuration file.
Regards,
Venkat (3 Replies)
Discussion started by: venkat55
3 Replies
6. UNIX for Dummies Questions & Answers
Hey guys ,
YEs this is probably silly for most but i am new to this forum and solaris . i am curious to know if the ip address we have for our solaris server is static or dhcp . how can i tell ? will ifconfig -a tell me this ? or other commands?
Thanks in advance (1 Reply)
Discussion started by: xdrivex
1 Replies
7. Red Hat
Hi All,
Could you please explain the purpose of assigning the static IP by using the DHCP Concept. Like by using the clients MAC address we assign the static IP Address. Waiting for your reply. Thanks in Advance. (6 Replies)
Discussion started by: Sharath Kumar
6 Replies
8. HP-UX
Hi,
I can find the IP details whether it is Static or dynamic in Linux machine from the location /etc/sysconfig/network-scripts/ifconfig-eth0 configuration file.
Can someone suggest a location to find the same in HP UX machines?
-Vivek (2 Replies)
Discussion started by: vkk
2 Replies
9. IP Networking
I'm trying to figure out what circumstances would cause an Open Solaris 11.2 host to switch itself from a static to a DHCP ip address upon reboot. This has only happened once but is a cause for some concern as this machine will be part of a web server pool.
Nothing has changed on the LAN that... (2 Replies)
Discussion started by: SmokeyJoe
2 Replies
10. Solaris
We have 2 solaris 10 t5240 servers with static IP addresses on nxge0 I/F which were rebooted a few days back with a known good config that has been in place for years (for /etc/hosts, /etc/hostname.nxge0, /etc/netmasks, etc)
They are not using dhcp.
About the same time today, both of their... (7 Replies)
Discussion started by: hdatontodo
7 Replies
LEARN ABOUT DEBIAN
guards
GUARDS(1) User Contributed Perl Documentation GUARDS(1)
NAME
guards - select from a list of files guarded by conditions
SYNOPSIS
guards [--prefix=dir] [--path=dir2:dir2:...] [--default=0|1] [-v|--invert-match] [--list|--check] [--config=file] symbol ...
DESCRIPTION
The script reads a configuration file that may contain so-called guards, file names, and comments, and writes those file names that satisfy
all guards to standard output. The script takes a list of symbols as its arguments. Each line in the configuration file is processed
separately. Lines may start with a number of guards. The following guards are defined:
+xxx Include the file(s) on this line if the symbol xxx is defined.
-xxx Exclude the file(s) on this line if the symbol xxx is defined.
+!xxx Include the file(s) on this line if the symbol xxx is not defined.
-!xxx Exclude the file(s) on this line if the symbol xxx is not defined.
- Exclude this file. Used to avoid spurious --check messages.
The guards are processed left to right. The last guard that matches determines if the file is included. If no guard is specified, the
--default setting determines if the file is included.
If no configuration file is specified, the script reads from standard input.
The --check option is used to compare the specification file against the file system. If files are referenced in the specification that do
not exist, or if files are not enlisted in the specification file warnings are printed. The --path option can be used to specify which
directory or directories to scan. Multiple directories are separated by a colon (":") character. The --prefix option specifies the
location of the files.
AUTHOR
Andreas Gruenbacher <agruen@suse.de> (SuSE Linux AG)
perl v5.14.2 2012-03-04 GUARDS(1)