Sponsored Content
Special Forums IP Networking How to configure DHCP to Static IP Post 24475 by Sirius Black on Friday 12th of July 2002 02:55:58 AM
Old 07-12-2002
if your router is a linux box, then you can change the file

/etc/init.d/network-scripts/ifcfg-ethx

where x is the interface number.
inside that file you can specify.

DHCP=no
ON BOOT = yes

IP_ADDR = "xxx.xxx.xxx.xxx" etc.

hope this helps.

- Sirius.
 

10 More Discussions You Might Find Interesting

1. HP-UX

HP-UX 10.xx Changing from static IP to DHCP

***Newbie alert*** What's the easiest way to accomplish this? An admin left our company and I have taken over his HP Workstation and moved it to a different location that is on a different IP segment. I have performed a number of google searches but the steps I have followed haven't worked. ... (1 Reply)
Discussion started by: Steelysteel
1 Replies

2. IP Networking

dhcp and static ip conflicts.

I have a USB Wireless Adapter using the rum0 driver. All I want to do is set a perminent static IP for the onboard wired interface elxl0. I can plumb the wired interface up fine on the fly, but when I try to save the static IP over a reboot, I lose the IP address assigned to rum0 from my wireless... (1 Reply)
Discussion started by: ts97783
1 Replies

3. IP Networking

Switching from DHCP to Static IP

I am trying to write a set of scripts for my Ubuntu 810 Server to allow a user to change from DHCP to a user-supplied Static IP, Subnet, Gateway and DNS Servers. So far I have the following, where $USERCHOICE is a user-entered value in each case: ifconfig eth0 down && ifconfig eth0 $USERCHOICE... (1 Reply)
Discussion started by: cleanden
1 Replies

4. Solaris

How to Configure a Static Ip Address

Hello friend, I am new in UNIX, but I want to learn a lot Well I have a problem to try to configure my PC with a static IP Address (IP 192.168.1.39, Mask 255.255.255.0, gateway 192.168.1.1) (DNS 200.48.225.130 and 200.48.225.146). where are the file that I must be change? The SO is Sun Solaris... (15 Replies)
Discussion started by: andresguillen
15 Replies

5. Red Hat

How to know whether my system is using DHCP or STATIC IP

Hi, I am using RHEL 5.1 and i would like to know, how to find the whether my system is using DHCP or STATIC IP with out looking at /etc/sysconfig/network-scripts/ifconfig-eth0 configuration file. Regards, Venkat (3 Replies)
Discussion started by: venkat55
3 Replies

6. UNIX for Dummies Questions & Answers

How to tell if i am using DHCP or Static

Hey guys , YEs this is probably silly for most but i am new to this forum and solaris . i am curious to know if the ip address we have for our solaris server is static or dhcp . how can i tell ? will ifconfig -a tell me this ? or other commands? Thanks in advance (1 Reply)
Discussion started by: xdrivex
1 Replies

7. Red Hat

Purpose of Static IP address through DHCP

Hi All, Could you please explain the purpose of assigning the static IP by using the DHCP Concept. Like by using the clients MAC address we assign the static IP Address. Waiting for your reply. Thanks in Advance. (6 Replies)
Discussion started by: Sharath Kumar
6 Replies

8. HP-UX

[Solved] Static or DHCP IP in HP-UX

Hi, I can find the IP details whether it is Static or dynamic in Linux machine from the location /etc/sysconfig/network-scripts/ifconfig-eth0 configuration file. Can someone suggest a location to find the same in HP UX machines? -Vivek (2 Replies)
Discussion started by: vkk
2 Replies

9. IP Networking

Node switched itself from static to DHCP on reboot issue

I'm trying to figure out what circumstances would cause an Open Solaris 11.2 host to switch itself from a static to a DHCP ip address upon reboot. This has only happened once but is a cause for some concern as this machine will be part of a web server pool. Nothing has changed on the LAN that... (2 Replies)
Discussion started by: SmokeyJoe
2 Replies

10. Solaris

Solaris static IP changed (non DHCP)

We have 2 solaris 10 t5240 servers with static IP addresses on nxge0 I/F which were rebooted a few days back with a known good config that has been in place for years (for /etc/hosts, /etc/hostname.nxge0, /etc/netmasks, etc) They are not using dhcp. About the same time today, both of their... (7 Replies)
Discussion started by: hdatontodo
7 Replies
LURKER-SEARCH(1)					      General Commands Manual						  LURKER-SEARCH(1)

NAME
lurker-search -- searches for messages in a lurker database SYNOPSIS
lurker-search [-c <config-file>] [-k <keyword>] [-d -f -i -v -q] [<terms>*] DESCRIPTION
lurker-search searches a lurker database the same way as the web interface. It can output summary information and delete messages. OPTIONS
-c config-file Use this config file for lurker settings. -k keyword Tag the matching messages with this keyword. -d Delete the messages found by this search -f Don't prompt before deleting -i Command line paramers are not search terms, but message IDs. -v Output message summary information -q Don't output message ids or status SEARCH TERMS
Lurker-search accepts these keywords for searching: -xxx select messages which do NOT match this term id:xxx select a message by the Message-ID field rt:xxx select messages which reply to the chosen Message-ID th:xxx select messages included in this thread ml:xxx select messages in this mailing list gr:xxx select messages in this mailing list group au:xxx select messages with this term in the author fields sb:xxx select messages with this word in the subject lang:xxx select messages in this language SEE ALSO
lurker-index(1), lurker-prune(1), lurker-params(1), lurker-list(1) lurker documentation on http://lurker.sourceforge.net/ COPYRIGHT
Copyright (C) 2002: Wesley W. Terpstra <terpstra@users.sourceforge.net> This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; version 2. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MER- CHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. BUGS
Before reporting a bug, please confirm that the bug you found is still present in the latest official release. If the problem persists, then send mail with instructions describing how to reproduce the bug to <lurker-users@lists.sourceforge.net>. LURKER-SEARCH(1)
All times are GMT -4. The time now is 10:26 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy